Registro
Condiciones del filtro
  • Rail Width W1(mm)
  • Assembly Height H(mm)
  • Rail Length L(mm)
      [470-969/1mm unidades]
    • Preload

      See the accuracy standard of each manufacturer.

      • Light Preload
    • Accuracy Standards

      See the accuracy standard of each manufacturer.

    • Nominal Part Number
    • L Dimension Type
    • Type
    • CAD
    • Días estimados de envío
      • Todo
      • En el plazo de 7 días laborables

    Opciones adicionales

    • Changes the rail mounting holes from counterbored holes to tapped holes.

    Miniature profiled rail guides / long carriage / high precision / material selectable (SSECBL13G-[470-969/1])

    Número de pieza:

    SSECBL13G-[470-969/1]
    Despejar
    Cantidad:

    Plano de contorno y tabla de especificaciones

    Back to the Category Linear Rail Guides / Profile Rail Guides

    Technical Drawing - Linear Rail Guides / Profile Rail Guides

     

    Miniature Linear Guides/Extra Long Block/Light Preload/Advanced Class/L Configurable:Related Image

     

    Available dimensions and tolerances can be found under the tab More Information .

     

    Basic Properties (e.g., material, hardness, coating, tolerance) - Linear Rail Guides / Profile Rail Guides

     

    Material
    Hardness
    TypeMX
    (Lubrication Unit)
    L Dimension
    Light PreloadSlight Clearance
    High GradeStandard Grade
    Stainless Steel
    56HRC~
    SSECBSSECBZBlank: None
    -MX: Provided
    Selectable
    SSECBLSSECBLZConfigurable
    Heat Resistant Temperature: -20 ~ 80°C

     

    Further specifications can be found under the tab More Information .

     

    More Information - Linear Rail Guides / Profile Rail Guides

     

    ■Precautions for Use
    Blocks are equipped with retainers (wire) to prevent balls from falling off. For how to handle the blocks, see >> P.525.
    Radial clearances and accuracies are not guaranteed if the blocks and rails are interchanged from the original set combinations.
    Straight grooves are provided on datum planes. Be sure to match the datum lines when using.
    Rails cannot be connected end to end.
    The accuracy of Linear Guides is guaranteed after mounting the rail (after fastening screws on the rail and pushing it onto the datum plane).
    Minor bending of the rail will be adjusted after being mounted and will not affect the performance.

    ■Accessory
    • H8 comes with cap screws (M2x6).

    ■Others
    • Filled with Lithium soap based grease (Multemp Grease PS2 by Kyodo Yushi Co., Ltd. ).
    • For Operating Life Calculation, see >> P. 527
    • For operating life calculations, use our free calculation software from http://download.misumi.jp/mol/fa_soft.html.
    • The MX type is greased with a lithium complex grease (TOUGHLIX GREASE MP2, made by JXTG Nippon Oil & Energy Corporation).

     

    Composition of a Product Code - Linear Rail Guides / Profile Rail Guides

     

    Part Number-L 
    SSECB10
    SSECB-MX10
    Miniature Linear Guides/Extra Long Block/Light Preload/Advanced Class/L Configurable:Related ImageSSECB10L
    Miniature Linear Guides/Extra Long Block/Light Preload/Advanced Class/L Configurable:Related ImageSSECB10G
    -
    -
    -
    -
    275
    275
    75
    75

    (With Lubrication Unit)
    (L Type Greased)
    (G Type Greased)
    Alternative grease types available
    >> P.531

     

    Alterations - Linear Rail Guides / Profile Rail Guides

     


    Miniature Linear Guides/Extra Long Block/Light Preload/Advanced Class/L Configurable:Related Image

    Here to the Overview of Options as PDF.

     

    General Information - Linear Rail Guides / Profile Rail Guides

     

     

    Selection details of profile rail guides with rolling elements

    - Material: steel, stainless steel

    - Coatings: uncoated, LTBC coated

    - Hardness: up to ~58HRC

    - Precision classes: standard class, high quality, precision class

    - Mounting height: 6 mm to 45 mm

    - Guide rail width: 5 mm to 42 mm

    - Guide rail length: 25 mm to 1960 mm

    - Pretension: slight play, slight pretension

    - Guide carriage versions: short, wide, wide and long, long, extra long

     

    Description/Basics

    A profile rail guide is a commonly used rolling linear guide in mechanical engineering.
    The advantages of this linear guide are its rigidity, carrying capacity, running accuracy and precision. The ball-bearing guide carriage (block/carriage) allows a limitless stroke over the length of the linear guide rail. Compared to linear guides guided against rollers, the balls in the guide carriage enable the achievement of high speeds.
    The linear guide rail and guide carriage are precisely coordinated and enable a high running accuracy for highly precise applications. It is therefore recommended purchasing the profile rail guide as a set for precise applications, as these are tested together for accuracy and precision.
    The profile rails are available in the MISUMI online shop in standardized lengths or configurable in 1 mm increments. The various additional options expand the versatility and possible applications.

     

    Useful Life

    After determining the permissible load, the useful life of a profile rail guide must be calculated depending on the application. This not only depends on the applied load, torque and lubrication, but also on many other factors. In the following link you will find the useful life calculation and design of profile rail guides.

    Note: MISUMI linear guides are coated with lubricants to protect them from oxidation during transport.

     

    Maintenance

     

    Lubricate the linear guide/lubrication intervals

    To reduce friction and wear, linear guides such as the profile rail guides should be lubricated regularly. The lubrication interval varies depending on the application and ambient condition, as this depends on many factors. The general recommended lubrication intervals of the profile rail guides are in the range of approx. 6 months. For long strokes, the lubrication intervals are reduced to approx. 3 months or every 1000 km. Here, too, it is recommended to check the lubrication performance initially at shorter intervals and to adjust it to the existing operating conditions. Too much lubricant should not be introduced into the linear guide, as too much lubricant can lead to increased resistance and damage.
    For smaller profile rail guides, such as miniature linear guides, the linear guide can be lubricated over the linear rail. For this purpose, the lubricant can be applied to the running surfaces of the linear rail.
    Structurally larger profile rail guides have a grease nipple to get the lubricant to the necessary areas.

     

    Alternative lubricants

    The MISUMI linear guides are pre-greased with the lubricant. As a standard, the profile rail guides are filled with lithium soap grease. The Multemp lubricant PS2 (from Kyodo Yushi Co. Ltd) is applied in the miniature profile rail guides. Profile rail guides for medium and heavy loads are pre-greased with Alvania Grease S2 (from Showa Shell Sekiyu K.K.). Alternatively, an alternative grease filling may be selected for the linear guide. For this purpose, a heat-resistant grease (L) and cleanroom-compatible grease (G) are available.

     

    Lubricant

    Designation

    Property

    L

    ET-100K (Kyodo Yushi)

    Heat and oxidation resistance, as well as high adhesion and cohesion strength. Low spray and leak probability

    G

    LG2 (NSK Ltd.)

    Cleanroom-compatible special lubricant for linear guides, ball screw, etc.

    Table showing the alternative lubricants

     

    Lubrication unit (MX)

    Another variant is the profile rail guide with lubrication unit (MX). The lubrication unit extends the lubrication intervals by supplying lubricant at the ends of the linear guide carriage. This means that not only the lubrication effort, but also the maintenance costs, can be reduced. The lubrication units are filled with lithium soap grease as standard.

     


    Profile rail guide with lubrication unit (MX)

     

    Function


    (1) Dust seal, (2) ball circulation, (3) guide carriage, (4) profile rail, (5) ball cage (wire), (6) ball

     

    In principle, the profile rail guide is provided with a ball bearing, which guides the balls back to the profile rail in a circular manner during the movement loop (closed system). As a result, this linear guide is not subject to any real stroke limit, except for the length of the guide rail used. The compact miniature profile rail guides have two ball revolving movements, the balls of which have contact at four points for the load suspension. Heavy duty and medium duty linear guides have four ball recirculations, each with contact at two points in X or O alignment. Lateral seals prevent dirt particles from penetrating, which protect the balls from heavy wear. A wire (ball cage) within the guide carriage makes it difficult for balls to fall out. This is essential for the function of the linear guide.

     

    Areas of Application

    MISUMI profile rail guides can be used in almost all linear movement applications.
    As opposed to other linear systems, the profile rail guide can absorb moments in different directions. This ensures rigidity in an application. Precision and running accuracy ensure precise guidance and movement. The profile rail guide can often be found in 3D printers, hoisting mechanisms, measuring devices, and positioning jigs. The linear guide is often used in conjunction with ball screw to achieve high positioning accuracy. MISUMI offers an additional option for the profile rail guide for parallel use [WC ], which sets the height difference to 15 μm under the rail pair.
    The compact design also allows these linear guides to be used in confined spaces.

     

    Materials

    The MISUMI miniature rail guides are available in stainless steel. Heavy-duty and medium-duty linear guides can be configured in steel and stainless steel.

     

    Coatings

    The profile rail guides are uncoated and available with an LTBC plating. The LTBC plating consists of a durable anodized fluoropolymer layer applied to the linear rail and guide carriage. It is resistant to flaking and offers good protection against corrosion.

     

    Dimensions

     

    Precision standards

    The precision standards such as standard class, high quality and precision class describe the dimensional manufacturing accuracy of the linear guides. More detailed information can be found under the tab Additional Information

    Information about running parallelism and dimensional accuracy can be found in this link.

     

    Instructions for Use / Installation Information - Linear Rail Guides / Profile Rail Guides

     

    Instructions for use

    Since the ball loop is completely run through in a certain stroke length, continuous short strokes are not recommended due to the distribution of the lubricant. With short strokes of the guide carriage, punctual wear may occur on the linear guide rail and balls as well as the linear guide can fail. In order for the lubricant to distribute evenly, sufficient stroke should be ensured when using a profile rail guide.
    The profile rail guides can be used in all orientations (levels). When replacing a guide carriage with a new one, it is recommended that the guide carriage be pushed against the profile rail carefully against the transport rail end. For pre-stressed linear guides, the removal of the guide carriage is generally not recommended, since balls can fall out of the guide carriage when reassembled.

    It should be noted that the profile rail guide should not bump. This may damage the balls in the guide carriage, impair function and ultimately lead to component failure.

     

     

    In general, it is not recommended to remove the guide carriage from the profile rail. If the guide carriage has to be removed from the guide rail, it is recommended to reverse the profile rail guide. This reduces the risk of balls falling should become loose. Slowly push the guide carriage (sled) off the profile rail. When replacing the guide carriage, push the profile rail straight and carefully into the guide carriage. If the linear rail is inserted at an angle, balls can fall out of the guide carriage and damage the plastic cage.

     

     

    Installation Information

     

    Reference surface of the profile rail guide

    In general, it is not recommended to remove the guide carriage from the profile rail. If the guide carriage has to be removed from the guide rail, it is recommended to reverse the profile rail guide. This reduces the risk of balls falling should become loose. Slowly push the guide carriage (sled) off the profile rail. When replacing the guide carriage, push the profile rail straight and carefully into the guide carriage. If the linear rail is inserted at an angle, balls can fall out of the guide carriage and damage the plastic cage.

     

    Miniature linear guide

    Medium and heavy duty linear guide

    Standard and C-value

    Standard linear guide

    Standard with plastic ball cage

    C-value

    Table showing the reference surfaces for linear guides: (1) reference surface marking, (2) reference surface (polished surface)

     

    The MISUMI profile rail guides are provided with reference surface markings for assembly. These are used for the alignment of the linear guides and as an indicator for the precisely manufactured reference surfaces. The reference surfaces serve as a reference for the contact surface of the base plate for the linear guide rail. Prior to assembly, the respective contact surfaces of the profile rail and base plate should be cleaned of any contamination.

     

    Fixation of the linear guide rail and guide carriage

     


    (1) Assembly with pusher plates, (2) assembly with tapered machine keys, (3) assembly with rail pusher plates

     

    For high precision applications and applications for loads as well as vibrations and impact, additional clamping against the reference surface is recommended. This can be achieved with pusher plates (1) on the guide carriage and guide rail. Another variant is clamping via tapered machine keys (2), which hold the linear rail and linear guide carriage in position via a spreading process. For long guide rails, rail pusher plates (3), which clamp and hold the profile rail to the reference surface of the base plate.

    For more information, see the Installation and Maintenance available as PDF

     

    Adjustment without base plate stopper

    - Position the profile rail on the base plate and fasten it temporarily with the screws (Fig. 1)
    - Place ruler with dial gauge parallel to linear rail.
    - Hand-tighten screws and perform the measuring process with the dial gauge and set parallelism.
    - Tighten screws to the recommended torque and fasten profile rail.
    - Like the first linear rail, the second linear rail can be adjusted using a ruler. However, the probability of high parallelism increases when the dial gauge is attached to the already mounted profile rail for measurement and adjustment. (Fig. 2)

     


    (1) Adjustment of first profile rail guide, (2) adjustment of second profile rail guide

     

    For more information, see the Installation and Maintenance available as PDF

     

    Application Examples - Linear Rail Guides / Profile Rail Guides

     

    Application example – linear guide as hoisting device with crank

    Application example – linear guide press

    Application example - positioning with air cylinder

    Application example – profile rail guide as XY coordinate stage

    Application example – linear guide with gripper

    Application example – profile rail guide with timing belt

       

    Supplementary Article

     

    Screws/bolts

     

    Linear guides (accessory)

     

    Ball screws

     

    Dowel pins/spring pins/stepped pins

     

    Profile rail guide (special versions)

     

    Industrial Applications

     

    3D printer industry
    Automotive industry
    Pharmaceutical industry
    Packaging industry

      

    Lista de números de pieza

    Número de artículos
    Número de pieza
    SSECBL13G-[470-969/1]

    Rail Width W1

    (mm)

    Assembly Height H

    (mm)

    Rail Length L

    (mm)

    Preload

    Accuracy Standards

    Nominal Part Number

    Lubrication Type

    Basic Load Rating: Dynamic Load

    (N)

    Basic Load Rating: Static Load

    (N)

    Allowable Static Moment MA

    (Nm)

    Allowable Static Moment MB

    (Nm)

    Allowable Static Moment MC

    (Nm)

    Grease Type

    L Dimension Type

    RoHS?Cantidad mínima de pedido
    12
    13
    470 ~ 969
    [Light Preload] Light Preload
    High Grade
    12
    -
    3600
    7600
    34.0
    34
    47.3
    Low Dust Generation Grease (G Type)
    Configurable Type
    10
    1 piezas
    Precio unitario (IVA no incluidos)(precio unitario IVA incluidos)
    Fecha de envío estándar
    -
    ( - )
    7 días laborables

    Información detallada

    Información básica

    MISUMI is getting quicker - Our average delivery time has been reduced to 5 days.

    Contorno y especificaciones

    Back to the Category Linear Rail Guides / Profile Rail Guides

    Technical Drawing - Linear Rail Guides / Profile Rail Guides

     

    Miniature Linear Guides/Extra Long Block/Light Preload/Advanced Class/L Configurable:Related Image

     

    Specification Tables - Linear Rail Guides / Profile Rail Guides

     

    Part NumberLBlock DimensionDowel Hole DimensionGuide Rail Dimension
    TypeMXHWL1BCSxℓL2KCbNC2(ℓ1)W1W2H1CaCounterbored HoleFG
    d1xd2xh
    SSECB
    SSECBL
    SSECBZ
    SSECBLZ
    -840~1301737.51220M2x2.527.56.50.38.5202754.70.32.4x4.2x2.3155
    Blank: None
    -MX: Provided
    1055~2752049.61526M3x338.67.80.310262.595.55.50.33.5x6x3.5207.5
    1370~4702754.82030M3x3.540.8100.513.5303127.57.50.53.5x6x4.52510
    16110~6703270.32540M3x455.3120.516404158.59.50.53.5x6x4.54015
    ■Table of Comparison with Standard Blocks
    • Shorter block length than Standard Type 2-Block.
    • Basic load rating C (dynamic) is enhanced up to 192% compared to 1 Block Type. H dimension can be reduced by using a long block.
    • Basic load rating C (static) is equivalent or higher compared to 1 Block/2 Block Type. 2 Block Type can make guide block length more compact.
    HBlock O.A.L. (L1)Basic Load Rating C (Dynamic) kNBasic Load Rating Co (Dynamic) kN
    Standard 1 BlockStandard 2 BlockExtra Long 1 BlockStandard 1 BlockStandard 2 BlockExtra Long 1 BlockStandard 1 BlockStandard 2 BlockExtra Long 1 Block
     Compared to Standard
    1 Block
    Compared to Standard
    2 Block
     Compared to Standard
    1 Block
    Compared to Standard
    2 Block
     Compared to Standard
    1 Block
    Compared to Standard
    2 Block
    823.647.237.5+13.9-9.70.91.81.5167%83%1.533.3220%110%
    10306049.6+19.6-10.41.532.5167%83%2.555200%100%
    1333.967.854.8+20.9-132.24.43.6164%82%3.36.67.6230%115%
    1642.484.870.3+27.9-14.53.67.26.9192%96%5.410.813.5250%125%

     

    Alterations - Linear Rail Guides / Profile Rail Guides

     

    Miniature Linear Guides/Extra Long Block/Light Preload/Advanced Class/L Configurable:Related Image

     

    More Information - Linear Rail Guides / Profile Rail Guides

     

    Miniature Linear Guides/Extra Long Block/Light Preload/Advanced Class/L Configurable:Related Image
    Miniature Linear Guides/Extra Long Block/Light Preload/Advanced Class/L Configurable:Related Image