¡Estamos traduciendo nuestra tienda online al español!
Pero como tenemos muchos productos y páginas, esto lleva tiempo. Mientras tanto, nuestro catálogo de productos estará en inglés. Gracias por su paciencia.
Inner Diameter Measuring Instruments
66 artículos
* Información sobre días de envío, gastos de envío y precios
MAHR
Self-centering dial bore gauge Marameter 844 NB
• Measuring head consists of a carbide-tipped, movable measuring pin and an opposing interchangeable stationary measuring probe with carbide ball• Movements of the measuring pin are transmitted to the indicating instrument via the ring segment• The broad centering bridge ensures automatic centering in the bore• Insensitive to temperature due to both the shaft and the transfer rod being made from Invar steel• Carbide-tipped measuring contacts for high wear resistanceMás informaciónConfigurarPrecio (IVA no incluido) a partir de:1,070.00 €Fecha de envío normal:7 días laborables
MITUTOYO
Digital ABSOLUTE Borematic (Internal)
This is a individual unit Three-Point Digimatic Snap Open Bore Gauge.It offers you the following benefits:- It enables you to take measurements easily and quickly.- Titanium-coated measuring pins gives you excellent durability and impact resistance.- 330° rotatable display unit also gives you easy reading at any angle.- GO/NG tolerance judgement function.Más informaciónConfigurarPrecio (IVA no incluido) a partir de:3,745.00 €Fecha de envío normal:5 días laborables
MITUTOYO
This is a Digimatic bore gauge that lets you take digital inside measurements with amazing accuracy even at the maximum 2 m depth.The ABSOLUTE Digimatic Bore Gauge offers you the following benefits:- Precision bore gauge lets you easily measure the diameter of deep bores without loss of accuracy.- You can store and recall up to 3 sets of master values and upper/lower tolerance values at the push of a button.GO/±NG judgement can be set. Up to max. four extension rods (250 or 500 mm) can be used.Más informaciónConfigurarPrecio (IVA no incluido) a partir de:1,478.00 €Fecha de envío normal:5 días laborables
MITUTOYO
Used for base point confirmation of internal micrometer, hole test, borematic, cylinder gauge, etc.Más informaciónConfigurarPrecio (IVA no incluido) a partir de:126.00 €Fecha de envío normal:5 días laborables
MAHR
Self-centring dial bore gauge Marameter 844 NH
• Measuring head consists of a carbide-tipped, movable measuring pin and an opposing interchangeable stationary counter probe with carbide ball• Movements of the measuring pin are transmitted to the indicating instrument via the ring segment• The broad centering bridge ensures automatic centering in the bore• Insensitive to temperature due to both the shaft and the transfer rod being made from Invar steel• Carbide-tipped measuring contacts for high wear resistanceMás informaciónConfigurarPrecio (IVA no incluido) a partir de:783.00 €Fecha de envío normal:7 días laborables- ConfigurarPrecio (IVA no incluido) a partir de:699.00 €Fecha de envío normal:7 días laborables
MAHR
Caliper gauge for internal measurement Marameter 838 TI
• Clearly identifiable tolerance markers• Carbide measuring contacts• Absolute measuring instrumentMás informaciónConfigurarPrecio (IVA no incluido) a partir de:699.00 €Fecha de envío normal:7 días laborables- ConfigurarPrecio (IVA no incluido) a partir de:718.40 €Fecha de envío normal:7 días laborables
MAHR
In addition to complete Dial Bore Gages 844 N, modular units can also be compiled as required to suit a individual measuring task and/or application.Measuring Head 844 Nk, steelMeasuring Head 844 NHk, carbide• With built-in lever transmission system, carbide-tipped anvil and extra-wide centering bridge. With interchangeable stationary anvil. Threaded connection for Holders 844 Ng and 844 Ngk.Extension Set 844 Nes• For extending range of Measuring Head 844 Nk/NHk from 250-400 mm to 800 mm. Consists of additional centering bridge and two extensions.Holder 844 Ng• Shank and transfer rod made of heat-resistant Invar steel. With a locking clamp for indicator.Short Holder 844 NgkShank and transfer rod made of heat-resistant Invar steel. With a locking clamp for an indicator.Right Angle Attachment 844 Nw• For measuring difficult to reach bores, e.g. in tight spaces, inconveniently located or on machine tools. For screwing in between 844 Ng or 844 Ngk and 844 Nk/NHK.Extension 844 Nv• For extra deep bores. For screwing in between 844 Ng and 844 Nk/NHk. Shank and transfer rod made of Invar steel.Más informaciónConfigurarPrecio (IVA no incluido) a partir de:180.50 €Fecha de envío normal:7 días laborables
MAHR
Self-centring dial bore gauge Marameter 844 N
• Measuring head consists of a carbide-tipped, movable measuring pin and an opposing interchangeable stationary counter probe with hardened steel ball• Movements of the measuring pin are transmitted to the indicating instrument via the ring segment• The broad centering bridge ensures automatic centering in the bore• Insensitive to temperature due to both the shaft and the transfer rod being made from Invar steel• High wear resistance due to carbide tipped moveable measuring pinMás informaciónConfigurarPrecio (IVA no incluido) a partir de:627.00 €Fecha de envío normal:7 días laborables
MITUTOYO
A Mitutoyo transfer gauge that enables the diameter of holes, bores or grooves to be measured with outside micrometers or calipers. In operation the spring loaded plunger is allowed to expand within the feature to be measured and then locked in place using the knurled rotary control on the end of the handle. In practice some manipulation is necessary to ensure that the minimum size has been captured, after which the gauge is carefully withdrawn so that the dimension across the contact surfaces can be measured.Más informaciónConfigurarPrecio (IVA no incluido) a partir de:58.00 €Fecha de envío normal:5 días laborables
MITUTOYO
A Mitutoyo transfer gauge that enables the diameter of holes, bores or grooves to be measured with outside micrometers or calipers. In operation the spring loaded plunger is allowed to expand within the feature to be measured and then locked in place using the knurled rotary control on the end of the handle. In practice some manipulation is necessary to ensure that the minimum size has been captured, after which the gauge is carefully withdrawn so that the dimension across the contact surfaces can be measured.Más informaciónConfigurarPrecio (IVA no incluido) a partir de:58.00 €Fecha de envío normal:5 días laborables
MITUTOYO
Stand for Bore Gauge Series 526
Quick stand for precision bore gauges, for serial inside measuring of small parts.Más informaciónConfigurarPrecio (IVA no incluido) a partir de:1,178.00 €Fecha de envío normal:60 días laborables
MITUTOYO
Internal Digital Caliper Gauge
A Mitutoyo internal digital caliper gauge designed for use as a comparator, to be set up using a setting ring or micrometer. The caliper is spring loaded and makes point contact at constant measuring force.Más informaciónConfigurarPrecio (IVA no incluido) a partir de:827.50 €Fecha de envío normal:5 días laborables
MITUTOYO
Internal Dial Caliper Gauge, Inch
This analog Internal Dial Caliper Gauge offers you the following benefits:- Excellent resistance against water and dust (IP65 protection level)- Optimized measuring force- Ergonomically designed to lie securely in your hand when measuringMás informaciónConfigurarPrecio (IVA no incluido) a partir de:712.50 €Fecha de envío normal:5 días laborables
MITUTOYO
A Mitutoyo internal dial caliper gauge designed for use as a comparator, to be set up using a setting ring or micrometer. The caliper is spring loaded and makes point contact at constant measuring force.Más informaciónConfigurarPrecio (IVA no incluido) a partir de:845.00 €Fecha de envío normal:5 días laborables
MITUTOYO
A set of six Mitutoyo transfer gauges that enables the diameter of holes, bores or grooves to be measured with outside micrometers or calipers. In operation the spring loaded plunger of a gauge is allowed to expand within the feature to be measured and then locked in place using the knurled rotary control on the end of the handle. In practice some manipulation is necessary to ensure that the minimum size has been captured, after which the gauge is carefully withdrawn so that the dimension across the contact surfaces can be measured. Enables small hole, bore and groove measurement using existing workshop tools. Knurled finish provides secure handling and easy locking.Más informaciónConfigurarPrecio (IVA no incluido) a partir de:324.00 €Fecha de envío normal:5 días laborables
MITUTOYO
A set of six Mitutoyo transfer gauges that enables the diameter of holes, bores or grooves to be measured with outside micrometers or calipers. In operation the spring loaded plunger of a gauge is allowed to expand within the feature to be measured and then locked in place using the knurled rotary control on the end of the handle. In practice some manipulation is necessary to ensure that the minimum size has been captured, after which the gauge is carefully withdrawn so that the dimension across the contact surfaces can be measured. Enables small hole, bore and groove measurement using existing workshop tools. Knurled finish provides secure handling and easy locking.Más informaciónConfigurarPrecio (IVA no incluido) a partir de:324.00 €Fecha de envío normal:5 días laborables
MITUTOYO
Digital Indicator, Bore Gauge ID-C, Inch/Metric
This indicator is designed for inside diameter measurement applications on bore gaugesIt offers the following benefits:- Minimum value holding function that allows you to easily detect a hole diameter.- Analogue bar graph in the display (12 different scales switchable)- The analogue bar graph enhances usability by adding a dial gauge “feel” to digital measurement.- GO/±NG tolerance judgement function- A fast measurement frequency mode(detection cycle 20ms or 50times/s) is selectable to measure in the peak detection mode more reliably.- Easy indicator setup via a setup menu- A USB interface box can be used to set up the indicator from PC via dedicated software.Más informaciónConfigurarPrecio (IVA no incluido) a partir de:563.00 €Fecha de envío normal:5 días laborables
MITUTOYO
Digital Indicator, Bore Gauge ID-C
This indicator is designed for inside diameter measurement applications on bore gaugesIt offers the following benefits:- Minimum value holding function that allows you to easily detect a hole diameter.- Analogue bar graph in the display (12 different scales switchable)- The analogue bar graph enhances usability by adding a dial gauge “feel” to digital measurement.- GO/±NG tolerance judgement function- A fast measurement frequency mode(detection cycle 20ms or 50times/s) is selectable to measure in the peak detection mode more reliably.- Easy indicator setup via a setup menu- A USB interface box can be used to set up the indicator from PC via dedicated software.Más informaciónConfigurarPrecio (IVA no incluido) a partir de:563.00 €Fecha de envío normal:60 días laborables
MITUTOYO
Digital ABSOLUTE Bore Gauge, Inch/Metric
A Mitutoyo ABSOLUTE Digimatic bore gauge designed exclusively for ID measurement. A minimum value holding function provides easy measurement of hole diameter. Up to three sets of master value and upper/lower tolerance values can be memorized and recalled at the push of a button. An analog bar indicator is integrated to enhance ease of reading, especially for GO/å±NG judgement. Measurements can be made inside very deep holes by using up to four extension rods.Más informaciónConfigurarPrecio (IVA no incluido) a partir de:1,478.00 €Fecha de envío normal:5 días laborables
MITUTOYO
Split-ball probes are protected by a diamond-like DLC coating.Split-ball probes are hard chrome platedDLC Black Diamond:- Extremely high wear protection, due to low frictional resistance- Safety due to high hardness and resistance- Safety due to sustained accuracy and precisionMás informaciónConfigurarPrecio (IVA no incluido) a partir de:121.00 €Fecha de envío normal:5 días laborables
MITUTOYO
Split-ball probes are protected by a diamond-like DLC coating.Split-ball probes are hard chrome platedDLC Black Diamond:- Extremely high wear protection, due to low frictional resistance- Safety due to high hardness and resistance- Safety due to sustained accuracy and precisionMás informaciónConfigurarPrecio (IVA no incluido) a partir de:55.92 €Fecha de envío normal:5 días laborables
ConfigurarPrecio (IVA no incluido) a partir de:1,867.50 €Fecha de envío normal:5 días laborables
MITUTOYO
Auxiliary Block Kit for Bore Gauge
This is an Auxiliary Block Kit that allows you to efficiently carry out reference-setting of dial bore gauges and tubular inside micrometers (18-150mm).Más informaciónConfigurarPrecio (IVA no incluido) a partir de:292.11 €Fecha de envío normal:5 días laborables
ConfigurarPrecio (IVA no incluido) a partir de:259.37 €Fecha de envío normal:5 días laborables
MITUTOYO
Used for quick and accurate setting of 2-Point Inside Measuring Instruments and 2-Point/3-Point Inside MicrometersNominal diameter is marked in 0.001 mm increments- Steel Setting Rings are available from 1 mm up to 300 mm and Ceramic Setting Rings from 4 mm up to 45 mmMás informaciónConfigurarPrecio (IVA no incluido) a partir de:268.00 €Fecha de envío normal:5 días laborables
MITUTOYO
Used for quick and accurate setting of 2-Point Inside Measuring Instruments and 2-Point/3-Point Inside MicrometersNominal diameter is marked in 0.001 mm increments- Steel Setting Rings are available from 1 mm up to 300 mm and Ceramic Setting Rings from 4 mm up to 45 mmMás informaciónConfigurarPrecio (IVA no incluido) a partir de:120.00 €Fecha de envío normal:5 días laborables
MAHR
Self-centering dial bore gauge Marameter 844 KC
Standard model• For indicating measurment of diameter and testing for roundness and conicity of bores• Especially suitable for testing batches• Determine the reversal point by rocking in the boreMás informaciónConfigurarPrecio (IVA no incluido) a partir de:1,005.00 €Fecha de envío normal:7 días laborables
MAHR
Inside measuring probe Marameter 844 KCk
Standard form with extremely wear resistant DLC-coated surface, ideal also for scratch-sensitive surfaces• For indicating measurment of diameter and testing for roundness and conicity of bores• Especially suitable for testing batches• Determine the reversal point by rocking in the boreMás informaciónConfigurarPrecio (IVA no incluido) a partir de:105.50 €Fecha de envío normal:7 días laborables
MAHR
Indicating plug gauge Marameter 844 DR-3
• Measuring head has a hard chrome plated cylinder guide and carbide-tipped anvils• The carbide expanding pin transfers radial movement to indicating instrument• Constant measuring force as a result of built-in spring, eliminating user influence• Extensive modular system is composed of measuring head, holder, depth extension, right angle attachments and depth stopsMás informaciónConfigurarPrecio (IVA no incluido) a partir de:897.00 €Fecha de envío normal:47 días laborables
MAHR
Indicating plug gauge Marameter 844 DS-F
• Measuring head has a hard chrome plated cylinder guide and carbide-tipped anvils• The carbide expanding pin transfers radial movement to indicating instrument• Constant measuring force as a result of built-in spring, eliminating user influence• Extensive modular system is composed of measuring head, holder, depth extension, right angle attachments and depth stopsMás informaciónConfigurarPrecio (IVA no incluido) a partir de:531.00 €Fecha de envío normal:47 días laborables
MAHR
Indicating plug gauge Marameter 844 D-FD
• Measuring head has a hard chrome plated cylinder guide and carbide-tipped anvils• The carbide expanding pin transfers radial movement to indicating instrument• Constant measuring force as a result of built-in spring, eliminating user influence• Extensive modular system is composed of measuring head, holder, depth extension, right angle attachments and depth stopsMás informaciónConfigurarPrecio (IVA no incluido) a partir de:432.00 €Fecha de envío normal:37 días laborables
MAHR
Indicating plug gauge Marameter 844 DS-HR
• Measuring head has a hard chrome plated cylinder guide and carbide-tipped anvils• The carbide expanding pin transfers radial movement to indicating instrument• Constant measuring force as a result of built-in spring, eliminating user influence• Extensive modular system is composed of measuring head, holder, depth extension, right angle attachments and depth stopsMás informaciónConfigurarPrecio (IVA no incluido) a partir de:627.00 €Fecha de envío normal:37 días laborables
MAHR
Self-centering dial bore gauge Marameter 844 K
High-precision comparative measurements of holes.Inside measuring probes from the 844 K family are 2-point comparative measuring instruments used to determine a reversing point in a bore by oscillation. This reversal point equates to the minimum and thus the exact bore diameter.Más informaciónConfigurarPrecio (IVA no incluido) a partir de:804.00 €Fecha de envío normal:7 días laborables
ConfigurarPrecio (IVA no incluido) a partir de:116.50 €Fecha de envío normal:7 días laborables
MAHR
Indicating plug gauge Marameter 844 DR
• Measuring probe made of hardened, stainless guide cylinder and carbide tipped probes • Carbide driving needle transfers radial measuring movement to the display unit • Constant measuring force as a result of built-in spring, eliminating user influence • Measuring head, measuring instrument holder, depth extensions, right angle attachments and depth stops form a comprehensive modular systemMás informaciónConfigurarPrecio (IVA no incluido) a partir de:362.00 €Fecha de envío normal:37 días laborables
MAHR
Indicating plug gauge Marameter 844 D-C
• Measuring probe made of hardened, stainless guide cylinder and diamond-tipped probes • Carbide driving needle transfers radial measuring movement to the display unit • Constant measuring force as a result of built-in spring, eliminating user influence • Measuring head, measuring instrument holder, depth extensions, right angle attachments and depth stops form a comprehensive modular systemMás informaciónConfigurarPrecio (IVA no incluido) a partir de:408.00 €Fecha de envío normal:39 días laborables
MAHR
Indicator holder Marameter 844 Kg / Kga / Kgz
Holder for mounting an indicator (comparator, dial gage or inductive probe) and connection of an 844 K/KC/KS inside measuring probe or corresponding accessories such as 844 Kt measuring depth extensions or 844 Kw right angle attachmentMás informaciónConfigurarPrecio (IVA no incluido) a partir de:96.50 €Fecha de envío normal:7 días laborables
MAHR
Extension for measuring depth, length (mm) Marameter 844 Kv
Application• To reach measuring points in deep boresProduct features• The measuring depth extension is screwed in between the holder (844 Kg/Kga) and the inside probe (844 K/KS/KS)Más informaciónConfigurarPrecio (IVA no incluido) a partir de:97.00 €Fecha de envío normal:7 días laborables
MAHR
The setting rings are used as dimensional standards for adjusting the bore gages 844 K/KC/KS to the respective nominal dimensionMás informaciónConfigurarPrecio (IVA no incluido) a partir de:161.00 €Fecha de envío normal:7 días laborables
MAHR
Transfer pin, carbide Marameter
Application• for inside measuring probe 844 K and 844 KCProduct features• Driving needle for transferring the measuring movement of the inside probe to the indicating measuring instrument• made of carbide for maximum service life and accuracyMás informaciónConfigurarPrecio (IVA no incluido) a partir de:104.00 €Fecha de envío normal:7 días laborables
MAHR
Extension for measuring depth Marameter 844 Dv
Application• For bore measurement at larger depths• Practical additional function as clamping shank for depth measuring stops 844 DtProduct features• The 844 Dv depth extensions are srewed in between holder 844 Dg and plug gage 844 D / 844 DR / 844 DS (if necessary right angle attachment 844 Dw)Más informaciónConfigurarPrecio (IVA no incluido) a partir de:122.50 €Fecha de envío normal:7 días laborables
MAHR
Indicating plug gauge Marameter 844 DR-M
• Measuring head made of hardened steel, hard chrome plated • Constant measuring force as a result of built-in spring, eliminating user influence • Extensive modular system is composed of measuring head, transfer needle, holder, depth extension, right angle attachments and setting rings • The minimum set of a measuring instrument consists of: Measuring head, transfer needle and holder plus indicator unitMás informaciónConfigurarPrecio (IVA no incluido) a partir de:445.00 €Fecha de envío normal:37 días laborables
MAHR
Indicating plug gauge Marameter 844 D-HR
• Measuring head made of hardened steel, hard chrome plated • Constant measuring force as a result of built-in spring, eliminating user influence • Extensive modular system is composed of measuring head, transfer needle, holder, depth extension, right angle attachments and setting rings • The minimum set of a measuring instrument consists of: Measuring head, transfer needle and holder plus indicator unitMás informaciónConfigurarPrecio (IVA no incluido) a partir de:450.00 €Fecha de envío normal:34 días laborables
