PET Plates (Dedicated for Chassis)

Click on this image to zoom in.

[Features]
Resin plate more economical than existing products.
[Difference From Conventional Products]
·2 thickness lineups of only 3 mm and 5 mm are available.
·Greater plate thickness tolerance compared to existing products.
　Plate Thickness 3 mm (Existing product: ±0.2 / This product: ±0.4), Plate Thickness 5 mm (Existing product: ±0.3 / This product: ±0.5)
·Smoke gray, antistatic smoke brown, and abrasion-resistant transparent colors are not available.

(i)Remark

Panel dimension must be set to A ≥ B.
Please note that the smoke brown of existing products and this product are different in color.
Notching for aluminum extrusions and relief at 4 corners will be machined to R2.5.
Depending on the size of the product, the price may be higher than existing products.

Part Number

Once your search is narrowed to one product,
the corresponding part number is displayed here.

Drawing / Specifications
3D Preview 3D preview is available after complete configuration
Part Numbers

■ Standard Type

[ ! ]A ≥ B

■Finish Condition

Plane	4 Sides	Plate Thickness Surface
Machining Method	Circular sawing	Material as is

■Hole Machined Type

[ ! ]A ≥ B

2HL

Hole Machining Details

N (Through Hole)

P (Countersink)

M (Threaded Insert)

Hole Machining Conditions (N·P·M)

Q (Keyhole)

Hole Machining Condition Q (Keyhole)

Ordering Code (Example) M4-L6
[ ! ]L ≤ T－1

* Keyhole Reference Position

[ ! ] Keyhole Machining Condition a ≥ 5, b ≥ 5, c ≥ 5

2H·4H·6H·8H

2HL

[Keyhole Position]
(1): For 2H, the center of diameter d₁ is consistent with G.
(2): For 4H and 6H, the center of G dimension is consistent with the center of B dimension.

(3): For 8H, the center of diameter d₁ of the middle keyhole is consistent with the center of B dimension.

(4): For 2HL, keyholes turn sideways and the center of diameter d₁ is consistent with F.

Screw Nominal Dia.	3	4	5	6	8	10
d	3.5	4.5	5.5	6.5	9	11
d₁	7.5	9.5	11.5	13.5	19	—
h	2	2.5	3	3.5	5	—

■ Table 1

Screw Nominal Dia.	3	4
d	3.5	4.5
L	3	4

Nominal Dia.	b (Min. Value)
3 to 10	2.5

Keyhole Nominal Dia.	5	6	8
d₁	6	7	9
d₂	14	16	20
h	11	12	15

[ ! ] Use with
flat washers
to prevent damage to the resin.

■Finish Condition

Plane	4 Sides	Plate Thickness Surface
Machining Method	Circular sawing	Material as is

■ Specification Table

Type	[M]Grade	Color	Operating Ambient Temperature
F-PYA	Standard	Transparent	-15 to 55°C
F-PYBA	Standard	Smoke Brown
F-PYTA	Antistatic	Transparent

■ Standard Type

Part Number	A	B	T
Standard Size	1 mm Increments		Selection
F-PYA (Standard, Transparent)	300 to 2000	300 to 1000	3·5
F-PYBA (Standard, Smoke Brown)
F-PYTA (Antistatic, Transparent)

■ Standard Type

Part Number	—	A	—	B	—	T
F-PYA	—	1200	—	800	—	5

■Hole Machined Type

Part Number	—	A	—	B	—	T	—	F	—	G	—	Screw Nominal Dia.	—	L
F-PYA4H	—	900	—	700	—	3	—	F750	—	G650	—	P3
F-PYBA4H	—	1200	—	800	—	5	—	F750	—	G650	—	M4	—	L4

■T Dimension Tolerance

T	T Dimension Tolerance
3	±0.4
5	±0.5

■Dimensional tolerance of A and B: ±1.0

■Hole Machined Type

Part Number		A	B	T	F	G	Bolt Nominal Dia. Selection
							Through Hole	Countersink	Keyhole	Threaded Insert
Type	Holes	1 mm Increments		Selection	0.5 mm Increments		N	P	Q	M	L
F-PYA (Standard, Transparent) F-PYBA (Standard, Smoke Brown) F-PYTA (Antistatic, Transparent)	2H (Horizontal) 2HL (Vertical) 4H 6H 8H	300 to 1200	300 to 1000	3	6 to 1191.5 (2H·4H) 4.5 to 1195.5 (2HL) 6 to 595.5 (6H·8H)	4.5 to 995.5 (2H) 6 to 991.5 (2HL·4H·6H) 6 to 495.5 (8H)	3 4 5 6 8 10	3	5 6 8	—	Select from Table 1


				5				3 4 5 6		3 4

[!] Dimension F Specification Range – 2H/4H type selection: d (d₁) + 2.5 ≤ F ≤ A - d (d₁) - 5; for 2HL: d (d₁) / 2 + 2.5 ≤ F ≤ A - d (d₁) / 2 - 2.5;
for 6H and 8H: d (d₁) + 2.5 ≤ F ≤ (A - d (d₁) - 5) / 2 is required.
[!] Dimension G Specification Range – 2H type selection: d (d₁) / 2 + 2.5 ≤ G ≤ B - d (d₁) / 2 - 2.5; for 2HL, 4H and 6H: d (d₁) + 2.5 ≤ G ≤ B - d (d₁) - 5;
for 8H: d (d₁) + 2.5 ≤ G ≤ (B - d (d₁) - 5) / 2 is required. (d for through hole, d₁ for countersink)

■T Dimension Tolerance

T	T Dimension Tolerance
3	±0.4
5	±0.5

■Dimensional tolerance of A and B: ±1.0

■Alterations

■ Standard Type

Part Number	—	A	—	B	—	T	—	(CRA, etc.)
F-PYA	—	1200	—	800	—	5	—	CRA30-CRC30

[ ! ] When specifying notching for aluminum extrusions and relief at 4 corners, the red circled part will be machined to R2.5.

Alterations	Aluminum Extrusion Notching for Blind Joint	Relief at 4 Corners	Corner Cut, Corner Radius Machining	Same Dimension Machining for 4 Corners
Alterations
Code	F□□, E□□, J□□, K□□	CN	CCA·CCB·CCC·CCD CRA·CRB·CRC·CRD	ACC	ACR
Spec.	Machines relief for blind joints of aluminum extrusions. [ ! ] Can only be specified for the standard sizes of standard types	Machines relief at 4 corners. CN = 1 mm Increments [ ! ]5 ≤ CN ≤ 50 Ordering Code CN = 25→CN25 [ ! ] Can only be specified for the standard sizes of standard types	Adds machining to any corner (ABCD). 5 mm Increments ·CCA5 = A Corner 5 mm Cut ·CRB5 = B corner 5 mm Radius Machining [ ! ] Can only be specified for the standard sizes of standard types [ ! ] Combination with same dimension machining for 4 corners is not available	All four corners can be cut and radius machined to the same dimensions (5 mm). ·ACC: Corner 5 mm Cut ·ACR: Corner 5 mm Radius Machining [ ! ] For the machining conditions of the hole and plate end face, see Hole Machining Conditions under Hole Machining Details

[List of Notching for Aluminum Extrusions]

Notching Shape by Joint	Single Joint Kit	Single Joint Kit Screw Joint Kit		Pre-Assembly Insertion Double Joint Kit		Center Joint	Post-Assembly Insertion Double Joint
	Single Joint Kit	Single Joint Kit Standard Type	Single Joint Kit Narrow Type, Screw Joint Kit	Standard Type	Offset Nut Type	Center Joint	Post-Assembly Insertion Double Joint
	(Example 1) (Example 2) For Example 2, panel notching is not required.		[ ! ] Illustration shows a Single Joint Kit Narrow Type.			(Example 1) (Example 2)
HFS5 Series 5	—	—		—	—
HFS5 Series 6
HFS5 Series 8	—
HFS5 Series 845	—					* Notching is not required.
HFS5 Series 10	—	—			—	—	—

[ ! ] When specifying notching for aluminum extrusions and relief at 4 corners, the red circled part will be machined to R2.5.

■Hole Machined Type

Alterations

Hole Position from Left

Hole Position from Bottom

Same Dimension Machining for 4 Corners

Code

ACC

ACR

Spec.

XC = 0.5 mm Increments

[ ! ] For the machining conditions of the hole and plate end face, see Hole Machining Conditions under Hole Machining Details

[ ! ] Can be specified only for Hole Machined Type (2H to 8H)

YC = 0.5 mm Increments

[ ! ] For the machining conditions of the hole and plate end face, see Hole Machining Conditions under Hole Machining Details

[ ! ] Can be specified only for Hole Machined Type (2H to 8H)

All four corners can be cut and
radius machined to the same dimensions (5 mm).
· ACC: Corner 5 mm Cut
· ACR: Corner 5 mm Radius Machining

[ ! ] For the machining conditions
of the hole and plate end face,
see Hole Machining Conditions
under Hole Machining Details

Hole Machining Type	b (Minimum Value)
Through Hole / Countersunk Hole Threaded Insert	2.5
Keyhole	5

Part Number:

3D preview is not available, because the part number has not yet been determined.

In order to open the 3D preview, the part number must be fixed.

Plug-in is required for 3D Preview

CAD Download

Data to be displayed: 30; 45; 60

Part Number
F-PYA2H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-1191.5/0.5]-G[4.5-995.5/0.5]-M3
F-PYA2H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-1191.5/0.5]-G[4.5-995.5/0.5]-N[3,5,6,10]
F-PYA2H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-1191.5/0.5]-G[4.5-995.5/0.5]-P[3,5,6]
F-PYA2H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-1191.5/0.5]-G[4.5-995.5/0.5]-Q[5,6]
F-PYA2HL-[300-1200/1]-[300-1000/1]-[3,5]-F[4.5-1195.5/0.5]-G[6-991.5/0.5]-M3
F-PYA2HL-[300-1200/1]-[300-1000/1]-[3,5]-F[4.5-1195.5/0.5]-G[6-991.5/0.5]-N[3,5,6,10]
F-PYA2HL-[300-1200/1]-[300-1000/1]-[3,5]-F[4.5-1195.5/0.5]-G[6-991.5/0.5]-P[3,5,6]
F-PYA2HL-[300-1200/1]-[300-1000/1]-[3,5]-F[4.5-1195.5/0.5]-G[6-991.5/0.5]-Q[5,6]
F-PYA4H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-1191.5/0.5]-G[6-991.5/0.5]-M3
F-PYA4H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-1191.5/0.5]-G[6-991.5/0.5]-N[3,5,6,10]
F-PYA4H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-1191.5/0.5]-G[6-991.5/0.5]-P[3,5,6]
F-PYA4H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-1191.5/0.5]-G[6-991.5/0.5]-Q[5,6]
F-PYA6H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-595.5/0.5]-G[6-991.5/0.5]-M3
F-PYA6H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-595.5/0.5]-G[6-991.5/0.5]-N[3,5,6,10]
F-PYA6H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-595.5/0.5]-G[6-991.5/0.5]-P[3,5,6]
F-PYA6H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-595.5/0.5]-G[6-991.5/0.5]-Q[5,6]
F-PYA8H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-595.5/0.5]-G[6-495.5/0.5]-M3
F-PYA8H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-595.5/0.5]-G[6-495.5/0.5]-N[3,5,6,10]
F-PYA8H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-595.5/0.5]-G[6-495.5/0.5]-P[3,5,6]
F-PYA8H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-595.5/0.5]-G[6-495.5/0.5]-Q[5,6]
F-PYA-[300-2000/1]-[300-1000/1]-[3,5]
F-PYBA2H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-1191.5/0.5]-G[4.5-995.5/0.5]-M[3,4]
F-PYBA2H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-1191.5/0.5]-G[4.5-995.5/0.5]-N[3,4,5,6,8,10]
F-PYBA2H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-1191.5/0.5]-G[4.5-995.5/0.5]-P[3,4,5,6]
F-PYBA2H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-1191.5/0.5]-G[4.5-995.5/0.5]-Q[5,6,8]
F-PYBA2HL-[300-1200/1]-[300-1000/1]-[3,5]-F[4.5-1195.5/0.5]-G[6-991.5/0.5]-M[3,4]
F-PYBA2HL-[300-1200/1]-[300-1000/1]-[3,5]-F[4.5-1195.5/0.5]-G[6-991.5/0.5]-N[3,4,5,6,8,10]
F-PYBA2HL-[300-1200/1]-[300-1000/1]-[3,5]-F[4.5-1195.5/0.5]-G[6-991.5/0.5]-P[3,4,5,6]
F-PYBA2HL-[300-1200/1]-[300-1000/1]-[3,5]-F[4.5-1195.5/0.5]-G[6-991.5/0.5]-Q[5,6,8]
F-PYBA4H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-1191.5/0.5]-G[6-991.5/0.5]-M[3,4]
F-PYBA4H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-1191.5/0.5]-G[6-991.5/0.5]-N[3,4,5,6,8,10]
F-PYBA4H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-1191.5/0.5]-G[6-991.5/0.5]-P[3,4,5,6]
F-PYBA4H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-1191.5/0.5]-G[6-991.5/0.5]-Q[5,6,8]
F-PYBA6H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-595.5/0.5]-G[6-991.5/0.5]-M[3,4]
F-PYBA6H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-595.5/0.5]-G[6-991.5/0.5]-N[3,4,5,6,8,10]
F-PYBA6H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-595.5/0.5]-G[6-991.5/0.5]-P[3,4,5,6]
F-PYBA6H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-595.5/0.5]-G[6-991.5/0.5]-Q[5,6,8]
F-PYBA8H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-595.5/0.5]-G[6-495.5/0.5]-M[3,4]
F-PYBA8H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-595.5/0.5]-G[6-495.5/0.5]-N[3,4,5,6,8,10]
F-PYBA8H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-595.5/0.5]-G[6-495.5/0.5]-P[3,4,5,6]
F-PYBA8H-[300-1200/1]-[300-1000/1]-[3,5]-F[6-595.5/0.5]-G[6-495.5/0.5]-Q[5,6,8]
F-PYBA-[300-2000/1]-[300-1000/1]-[3,5]

Minimum order quantity	Standard Shipping Days ?	Grade	Color	Shape	Hole Machining	[A] Length (Plate) (mm )	[B] Width (Plate) (mm )	[T] Thickness (Plate) (mm )	[F] Distance (mm )	[G] Distance (mm )	[N] Diameter (Through Hole) (mm)	[P] Diameter (Countersink) (mm)	[Q] Diameter (Keyhole) (mm)	[M] Diameter (Threaded Insert)
1	9 Days	Standard	Transparent	Hole Machining	２H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 1191.5	4.5 ～ 995.5	-	-	-	3
1	9 Days	Standard	Transparent	Hole Machining	２H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 1191.5	4.5 ～ 995.5	3 ～ 10	-	-	-
1	9 Days	Standard	Transparent	Hole Machining	２H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 1191.5	4.5 ～ 995.5	-	3 ～ 6	-	-
1	9 Days	Standard	Transparent	Hole Machining	２H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 1191.5	4.5 ～ 995.5	-	-	5 ～ 6	-
1	9 Days	Standard	Transparent	Hole Machining	2HL	300 ～ 1200	300 ～ 1000	3 ～ 5	4.5 ～ 1195.5	6 ～ 991.5	-	-	-	3
1	9 Days	Standard	Transparent	Hole Machining	2HL	300 ～ 1200	300 ～ 1000	3 ～ 5	4.5 ～ 1195.5	6 ～ 991.5	3 ～ 10	-	-	-
1	9 Days	Standard	Transparent	Hole Machining	2HL	300 ～ 1200	300 ～ 1000	3 ～ 5	4.5 ～ 1195.5	6 ～ 991.5	-	3 ～ 6	-	-
1	9 Days	Standard	Transparent	Hole Machining	2HL	300 ～ 1200	300 ～ 1000	3 ～ 5	4.5 ～ 1195.5	6 ～ 991.5	-	-	5 ～ 6	-
1	9 Days	Standard	Transparent	Hole Machining	4H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 1191.5	6 ～ 991.5	-	-	-	3
1	9 Days	Standard	Transparent	Hole Machining	4H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 1191.5	6 ～ 991.5	3 ～ 10	-	-	-
1	9 Days	Standard	Transparent	Hole Machining	4H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 1191.5	6 ～ 991.5	-	3 ～ 6	-	-
1	9 Days	Standard	Transparent	Hole Machining	4H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 1191.5	6 ～ 991.5	-	-	5 ～ 6	-
1	9 Days	Standard	Transparent	Hole Machining	6H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 595.5	6 ～ 991.5	-	-	-	3
1	9 Days	Standard	Transparent	Hole Machining	6H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 595.5	6 ～ 991.5	3 ～ 10	-	-	-
1	9 Days	Standard	Transparent	Hole Machining	6H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 595.5	6 ～ 991.5	-	3 ～ 6	-	-
1	9 Days	Standard	Transparent	Hole Machining	6H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 595.5	6 ～ 991.5	-	-	5 ～ 6	-
1	9 Days	Standard	Transparent	Hole Machining	8H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 595.5	6 ～ 495.5	-	-	-	3
1	9 Days	Standard	Transparent	Hole Machining	8H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 595.5	6 ～ 495.5	3 ～ 10	-	-	-
1	9 Days	Standard	Transparent	Hole Machining	8H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 595.5	6 ～ 495.5	-	3 ～ 6	-	-
1	9 Days	Standard	Transparent	Hole Machining	8H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 595.5	6 ～ 495.5	-	-	5 ～ 6	-
1	5 Days	Standard	Transparent	No Hole Machining (Standard)	No Hole Machining (Standard Type)	300 ～ 2000	300 ～ 1000	3 ～ 5	-	-	-	-	-	-
1	9 Days	Standard	Smoke Brown	Hole Machining	２H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 1191.5	4.5 ～ 995.5	-	-	-	3 ～ 4
1	9 Days	Standard	Smoke Brown	Hole Machining	２H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 1191.5	4.5 ～ 995.5	3 ～ 10	-	-	-
1	9 Days	Standard	Smoke Brown	Hole Machining	２H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 1191.5	4.5 ～ 995.5	-	3 ～ 6	-	-
1	9 Days	Standard	Smoke Brown	Hole Machining	２H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 1191.5	4.5 ～ 995.5	-	-	5 ～ 8	-
1	9 Days	Standard	Smoke Brown	Hole Machining	2HL	300 ～ 1200	300 ～ 1000	3 ～ 5	4.5 ～ 1195.5	6 ～ 991.5	-	-	-	3 ～ 4
1	9 Days	Standard	Smoke Brown	Hole Machining	2HL	300 ～ 1200	300 ～ 1000	3 ～ 5	4.5 ～ 1195.5	6 ～ 991.5	3 ～ 10	-	-	-
1	9 Days	Standard	Smoke Brown	Hole Machining	2HL	300 ～ 1200	300 ～ 1000	3 ～ 5	4.5 ～ 1195.5	6 ～ 991.5	-	3 ～ 6	-	-
1	9 Days	Standard	Smoke Brown	Hole Machining	2HL	300 ～ 1200	300 ～ 1000	3 ～ 5	4.5 ～ 1195.5	6 ～ 991.5	-	-	5 ～ 8	-
1	9 Days	Standard	Smoke Brown	Hole Machining	4H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 1191.5	6 ～ 991.5	-	-	-	3 ～ 4
1	9 Days	Standard	Smoke Brown	Hole Machining	4H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 1191.5	6 ～ 991.5	3 ～ 10	-	-	-
1	9 Days	Standard	Smoke Brown	Hole Machining	4H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 1191.5	6 ～ 991.5	-	3 ～ 6	-	-
1	9 Days	Standard	Smoke Brown	Hole Machining	4H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 1191.5	6 ～ 991.5	-	-	5 ～ 8	-
1	9 Days	Standard	Smoke Brown	Hole Machining	6H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 595.5	6 ～ 991.5	-	-	-	3 ～ 4
1	9 Days	Standard	Smoke Brown	Hole Machining	6H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 595.5	6 ～ 991.5	3 ～ 10	-	-	-
1	9 Days	Standard	Smoke Brown	Hole Machining	6H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 595.5	6 ～ 991.5	-	3 ～ 6	-	-
1	9 Days	Standard	Smoke Brown	Hole Machining	6H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 595.5	6 ～ 991.5	-	-	5 ～ 8	-
1	9 Days	Standard	Smoke Brown	Hole Machining	8H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 595.5	6 ～ 495.5	-	-	-	3 ～ 4
1	9 Days	Standard	Smoke Brown	Hole Machining	8H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 595.5	6 ～ 495.5	3 ～ 10	-	-	-
1	9 Days	Standard	Smoke Brown	Hole Machining	8H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 595.5	6 ～ 495.5	-	3 ～ 6	-	-
1	9 Days	Standard	Smoke Brown	Hole Machining	8H	300 ～ 1200	300 ～ 1000	3 ～ 5	6 ～ 595.5	6 ～ 495.5	-	-	5 ～ 8	-
1	5 Days	Standard	Smoke Brown	No Hole Machining (Standard)	No Hole Machining (Standard Type)	300 ～ 2000	300 ～ 1000	3 ～ 5	-	-	-	-	-	-

Basic information

Material	PET

Configure

42Suggestion of an applicable part number.

View Part Numbers

Some specification is not specified yet.

The part number is completed.

Basic Attributes

Color
- Transparent
- Smoke Brown
Clear
Shape
- No Hole Machining (Standard)
- Hole Machining
Clear
Hole Machining
- No Hole Machining (Standard Type)
- ２H
- 2HL
- 4H
- 6H
- 8H
Clear
[A] Length (Plate)(mm )
[300-2000/1mm Unit(s)]
Clear
[B] Width (Plate)(mm )
[300-1000/1mm Unit(s)]
Clear
[T] Thickness (Plate)(mm )
- 3
- 5
Clear
[F] Distance(mm )
[4.5-1195.5/0.5mm Unit(s)]
Clear
[G] Distance(mm )
[4.5-995.5/0.5mm Unit(s)]
Clear
[N] Diameter (Through Hole) (mm)
- 3
- 4
- 5
- 6
- 8
- 10
Clear
[P] Diameter (Countersink) (mm)
- 3
- 4
- 5
- 6
Clear
[Q] Diameter (Keyhole) (mm)
- 5
- 6
- 8
Clear
[M] Diameter (Threaded Insert)
- 3
- 4
Clear
Type
- F-PYA
- F-PYA2H
- F-PYA2HL
- F-PYA4H
- F-PYA6H
- F-PYA8H
- F-PYBA
- F-PYBA2H
- F-PYBA2HL
- F-PYBA4H
- F-PYBA6H
- F-PYBA8H
- F-PYTA
- F-PYTA2H
- F-PYTA2HL
- F-PYTA4H
- F-PYTA6H
- F-PYTA8H
Clear
Grade
- Standard
- Antistatic
Clear
Filter by CAD data type
- 2D
- 3D
Clear