OSG Screw-Hole-Related Tools（Coating Y/N：Available）
Search by sub-category
Hand Taps
Spiral Taps
Point Taps
Roll Taps
Taps for Pipes
Thread Cutters
Thread-Cutting-Related Tools
Dies
Modification/Removal Tools
| Shipping Days |
|
|---|
?* Information on days to ship and prices
-
- Promotional pricing
A Tap Series, Spiral Tap, A-SFT
OSG
Has stable chip extraction and can be used for various work materials in a wide range of cutting areas and machines. Mainly spiral taps with spiral shaped grooves used in the blind holes.- Volume Discount
Starting from∗ ： 16.04 € Special price Min. Shipping Days ： Same day *Unit price with basic configuration
-
Groove-Free Tap Series VP New Roll VP-NRT
OSG
Powdered high-speed steel and special thread design provide long-life processing in wide range of workpieces.- Volume Discount
Min. Shipping Days ： 6 Days -
A Tap Series Point Tap Long Shank A-LT-POT
OSG
Has stable chip extraction and can be used for various work materials in a wide range of cutting areas and machines. Point taps with points grooves that are used in through holes.Starting from∗ ： 23.65 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Hand Tap Series, Hand Taps for Super High Hardness Steel, VX-OT
OSG
Suitable for 50 HRC and up Tempered Steel (Alloy Steel, Die Steel, Tool Steel, Etc.) TappingStarting from∗ ： 83.15 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
A Tap Series, Spiral Tap, Long Shank A-LT-SFT
OSG
Has stable chip extraction and can be used for various work materials in a wide range of cutting areas and machines. Mainly spiral taps with spiral shaped grooves used in the blind holes.Starting from∗ ： 24.50 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
- Promotional pricing
Spiral Tap Series, V Coated, V-SFT
OSG
Can be used on a wide variety of materials soft materials to hard materials. Particularly suited for tapping under high speed, high dilution (water soluble cutting fluid) conditions.- Volume Discount
Starting from∗ ： 17.63 € Special price Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Planet Cutter Series Small Diameter Planet Cutters WH-VM-PNC
OSG
The planet cutter is able to mill M1 - M5 small diameter female screws. Ideal for Preventing Defects in High Value Added Manufactured Articles and for Tapping without a Pilot Hole Margin- Volume Discount
Starting from∗ ： 101.50 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
- Promotional pricing
Hand Tap Series, V Coating Powder High Speed (High Hardness Steel), V-XPM-HT
OSG
Suitable for 42-52 HRC tempered steel (alloy steel, die steel, tool steel, etc.) tapping. Excellent Abrasion Resistant V Coating Has Been Applied to Maximize the Properties of the Base Material on the Surface- Volume Discount
Starting from∗ ： 26.47 € Special price Min. Shipping Days ： Same day *Unit price with basic configuration
-
Planet Cutter Series NC-Planet Cutters WX-PNC
OSG
Different threads can be processed with the same pitch using a single piece. Both right-handed and left-handed threads can be processed.- Volume Discount
Starting from∗ ： 158.30 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Planet Cutter Series Super Planet with Oil Holes DR-O-PNAC
OSG
A Single Piece Can be Used as a Complex Tool, for Pilot Hole Drilling + Chamfering + Female Thread Processing, Reducing Unnecessary Non-Processing Time in Tool Changes and Improving ProductivityStarting from∗ ： 324.46 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Planet Cutter Series Planet Cutters with Oil Holes for Steel WXO-ST-PNC
OSG
By spraying machining oil compound from the lubrication hole, allows effective removal of cutting debris.Starting from∗ ： 165.90 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Groove-Free Tap Series VP New Roll Long Shank VP-LT-NRT
OSG
Powdered high-speed steel and special thread design provide long-life processing in wide range of workpieces.Starting from∗ ： 24.43 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Starting from∗ ： 24.10 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Hand Tap Series, Hand Taps for Super High Hardness Steel, WH55-OT
OSG
Suitable for threading hardened steel up to 55 HRC.
Material: High hardness steel up to 55 HRC
For coating / surface treatment / steel
Accuracy (class) OH3- Volume Discount
Starting from∗ ： 83.34 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Hand Tap Series, Tin Coated, TIN-HT
OSG
Excellent cutting edge strength makes it suitable for high hardness material machining without chipping.- Volume Discount
Starting from∗ ： 16.26 € Min. Shipping Days ： 8 Days *Unit price with basic configuration
-
Planet Cutter Series Super Planet DR-PNAC
OSG
A Single Piece Can be Used as a Complex Tool, for Pilot Hole Drilling + Chamfering + Female Thread Processing, Reducing Unnecessary Non-Processing Time in Tool Changes and Improving ProductivityStarting from∗ ： 295.75 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
- Promotional pricing
Groove-Free Tap Series, Tin Coated, TIN-NRT
OSG
Suitable for both steel and non-ferrous alloys. Capable of high-speed cutting and efficient tapping; offer drastically improved durability.- Volume Discount
Starting from∗ ： 17.52 € Special price Min. Shipping Days ： Same day *Unit price with basic configuration
-
A Tap Series for Pipes Point Tap A-POT
OSG
Has stable chip extraction and can be used for various work materials in a wide range of cutting areas and machines. Point taps with points grooves that are used in through holes.- Volume Discount
Starting from∗ ： 15.94 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Spiral Tap Series, HR Coated, for Heat-Resistant Nickel-Based Superalloys, WHR-NI-SFT
OSG
Combining spiral tap with knurled flutes has brought in highly rigid edges. Assure long-lasting, stable machining of nickel-based alloy (40 - 45 HRC) processed under aging treatment.Starting from∗ ： 22.41 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Spiral Tap Series, for Stainless Steel (Compatible with Water-Soluble Cutting Oil) CC-SUS-SFT
OSG
Allows internal threading of stainless steel with a water soluble cutting fluid.
Tool material: Vanadium high speed steel
Hole type: For blind holes
Material: General steel/stainless steel.- Volume Discount
Starting from∗ ： 17.56 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Point Tap Series, HR Coating, for NI-Base Heat Resistant Alloys, WHR-NI-POT
OSG
In applying HR coating with high welding-resisting properties on nickel based alloys, it achieves a long operating life even on aging nickel based alloys (40-45 HRC)Starting from∗ ： 28.34 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Insert Screw Tap Series, New Roll Tap for Non-Irons, Long Shank, HL-LT-B-NRT
OSG
When cutting aluminum (cast, rolled and forged) and other light alloys, this is suitable as a countermeasure for obstruction from metal shavings, or when the objective is extending the tap usage life.Starting from∗ ： 42.36 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Spiral Tap Series, Tin Coated, TIN-SFT
OSG
The length of the main screw is processed under 2D, making it ideal for tapping bases and insides of carbon steel and stainless steel using water-soluble cutting fluid.- Volume Discount
Starting from∗ ： 16.04 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Spiral Tap Series, Tin Coated, Long Shank, TIN-LT-SFT
OSG
The length of the main screw is processed under 2D, making it ideal for tapping bases and insides of carbon steel and stainless steel using water-soluble cutting fluid.- Volume Discount
Starting from∗ ： 23.77 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Spiral Tap Series, V Coating Powder High-Speed Steel, VP-SFT
OSG
Optimal for machining pre-hardened steel alloys from 35 to 42 HRC.
Tool material: Powder metal high-speed steel
Thread type: Metric
Hole type: For blind holes
Material: General steel / heat-treated steel
Coating: Surface treatment for steel.Starting from∗ ： 17.33 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Spiral Tap Series, High-Speed Synchronized Tap Long Shank HS-LT-SFT
OSG
Suited for blind thread cutting using machinery equipped with complete lead feeding mechanisms.Starting from∗ ： 32.98 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Spiral Tap Series, for Copper, CU-SFT
OSG
Treated With CRN Coating Which Shows Excellent Friction Resistance and Anti-Sticking Properties Against Copper and Use of HSSE as Material Allows Long Lived Machining on Copper- Volume Discount
Starting from∗ ： 26.27 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Planet Cutter Series MC-Planet Cutters PNGT
OSG
Different threads can be processed with the same pitch using a single piece. Both right-handed and left-handed threads can be processed.Starting from∗ ： 205.83 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Point Tap Series, Tin Coated, TIN-POT
OSG
Though workpiece can be widely applied, it is suitable for high speed tapping of through holes, such as tempered material, and especially stainless steel- Volume Discount
Starting from∗ ： 15.45 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Point Tap Series, TIN Coating, Long Shank, TIN-LT-POT
OSG
Though workpiece can be widely applied, it is suitable for high speed tapping of through holes, such as tempered material, and especially stainless steel- Volume Discount
Starting from∗ ： 22.83 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Point Tap Series, V Coated, V-POT
OSG
Compatible with a wide range of materials - soft materials to hard materials. Displays particularly good performance in tapping under high speed, highly dilution (water soluble cutting fluid) conditions. Also Effective For Dry-Tapping- Volume Discount
Starting from∗ ： 24.73 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Point Tap Series, V Coating, Long Shank, V-LT-POT
OSG
Compatible with a wide range of materials - soft materials to hard materials. Displays particularly good performance in tapping under high speed, highly dilution (water soluble cutting fluid) conditions. Also Effective For Dry-TappingStarting from∗ ： 23.17 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Point Tap Series, Ultra Synchronizing Taps, HS-RFT
OSG
Suited for through thread cutting using machinery equipped with complete lead feeding mechanisms.- Volume Discount
Starting from∗ ： 30.20 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Point Tap Series, High Speed Synchronizing Taps, JIS Shank, J-HS-RFT
OSG
Suited for through thread cutting using machinery equipped with complete lead feeding mechanisms.- Volume Discount
Starting from∗ ： 21.73 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Point Tap Series, High Speed Synchronizing Taps, Long Shank, HS-LT-RFT
OSG
Suited for through thread cutting using machinery equipped with complete lead feeding mechanisms.Starting from∗ ： 27.13 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Taper Tap Series for Pipes TIN Coated TIN-TPT
OSG
TIN coating with excellent solvent resistance, abrasion resistance has been applied.- Volume Discount
Starting from∗ ： 30.48 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Taper Tap Series for Pipes TIN Coating Interrupted Thread TIN-IRT
OSG
TIN coating with excellent solvent resistance, abrasion resistance has been applied.- Volume Discount
Starting from∗ ： 39.15 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Taper Tap Series for Pipes TIN Coating Interrupted Thread Short Screws TIN-S-IRT
OSG
TIN coating with excellent solvent resistance, abrasion resistance has been applied.Starting from∗ ： 41.25 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Taper Tap Series for Pipes TIN Coated Short Screws TIN-S-TPT
OSG
TIN coating with excellent solvent resistance, abrasion resistance has been applied.- Volume Discount
Starting from∗ ： 31.88 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Taper Tap Series for Pipes V Coating Powder HSS (For High Hardness Steel) V-XPM-TPT
OSG
Used for machining of pipe taper female threads, but is suitable for easy processing conditionsStarting from∗ ： 45.80 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Taper Tap Series for Pipes V Coated Carbide (For High Hardness Steel) VX-TPT
OSG
Exhibits Exceptional Power Toward 50-60 HRC and up Tempered Steel (Alloy Steel, Die Steel, Tool Steel, etc.)Starting from∗ ： 168.46 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Taper Tap Series for Pipes For Aluminum V-AL-TPT
OSG
Ideal for taper female screw machining for aluminum alloy tube, as gouging of female screw occurs easily- Volume Discount
Starting from∗ ： 27.23 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Groove-Free Tap Series IT New Roll IT-NRT
OSG
Powdered high-speed steel and special thread design provide long-life processing in wide range of workpieces.- Volume Discount
Starting from∗ ： 19.82 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Groove-Free Tap Series TIN Coated Long Shank TIN-LT-NRT
OSG
Suitable for both steel and non-ferrous alloys. Capable of high-speed cutting and efficient tapping; offer drastically improved durability.Starting from∗ ： 24.43 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
-
Groove-Free Tap Series UM New Roll UM-NRT
OSG
Powdered high-speed steel and special thread design provide long-life processing in wide range of workpieces.- Volume Discount
Starting from∗ ： 31.64 € Min. Shipping Days ： 6 Days *Unit price with basic configuration
| Brand |
|---|
| Product Series |
| Starting from∗ |
| Min. Shipping Days ： |
| Screw Types |
| Screw size (Nominal) |
| Pitch (P), Number of Threading(mm) |
| Chamfer threads (Lcf) |
| Tool Material Type |
| work material |
| Tap Type |
| Hole type |
| Coating Y/N |
| Coating Type |
| Overall Length (L)(mm) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Brand | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG | OSG |
| Product Series | Hand Tap Series, Hand Taps for Super High Hardness Steel, VX-OT | Planet Cutter Series Small Diameter Planet Cutters WH-VM-PNC | Hand Tap Series, V Coating Powder High Speed (High Hardness Steel), V-XPM-HT | Planet Cutter Series Planet Cutters with Oil Holes for Steel WXO-ST-PNC | Hand Tap Series, Hand Taps for Super High Hardness Steel, WH55-OT | Spiral Tap Series, HR Coated, for Heat-Resistant Nickel-Based Superalloys, WHR-NI-SFT | Spiral Tap Series, for Stainless Steel (Compatible with Water-Soluble Cutting Oil) CC-SUS-SFT | Point Tap Series, HR Coating, for NI-Base Heat Resistant Alloys, WHR-NI-POT | Insert Screw Tap Series, New Roll Tap for Non-Irons, Long Shank, HL-LT-B-NRT | Spiral Tap Series, V Coating Powder High-Speed Steel, VP-SFT | Spiral Tap Series, High-Speed Synchronized Tap Long Shank HS-LT-SFT | Point Tap Series, High Speed Synchronizing Taps, JIS Shank, J-HS-RFT | Point Tap Series, High Speed Synchronizing Taps, Long Shank, HS-LT-RFT | Taper Tap Series for Pipes TIN Coating Interrupted Thread TIN-IRT | Taper Tap Series for Pipes TIN Coating Interrupted Thread Short Screws TIN-S-IRT | Taper Tap Series for Pipes TIN Coated Short Screws TIN-S-TPT | Taper Tap Series for Pipes V Coating Powder HSS (For High Hardness Steel) V-XPM-TPT | Taper Tap Series for Pipes V Coated Carbide (For High Hardness Steel) VX-TPT | |||||||||||||||||||||||||||
| Starting from∗ | 16.04 € Special price *Unit price with basic configuration Promotional pricingVolume Discount | - Volume Discount | 23.65 € *Unit price with basic configuration | 83.15 € *Unit price with basic configuration | 24.50 € *Unit price with basic configuration | 17.63 € Special price *Unit price with basic configuration Promotional pricingVolume Discount | 101.50 € *Unit price with basic configuration Volume Discount | 26.47 € Special price *Unit price with basic configuration Promotional pricingVolume Discount | 158.30 € *Unit price with basic configuration Volume Discount | 324.46 € *Unit price with basic configuration | 165.90 € *Unit price with basic configuration | 24.43 € *Unit price with basic configuration | 24.10 € *Unit price with basic configuration Volume Discount | 83.34 € *Unit price with basic configuration Volume Discount | 16.26 € *Unit price with basic configuration Volume Discount | 295.75 € *Unit price with basic configuration | 17.52 € Special price *Unit price with basic configuration Promotional pricingVolume Discount | 15.94 € *Unit price with basic configuration Volume Discount | 22.41 € *Unit price with basic configuration | 17.56 € *Unit price with basic configuration Volume Discount | 28.34 € *Unit price with basic configuration | 42.36 € *Unit price with basic configuration | 16.04 € *Unit price with basic configuration Volume Discount | 23.77 € *Unit price with basic configuration Volume Discount | 17.33 € *Unit price with basic configuration | 32.98 € *Unit price with basic configuration | 26.27 € *Unit price with basic configuration | 205.83 € *Unit price with basic configuration | 15.45 € *Unit price with basic configuration Volume Discount | 22.83 € *Unit price with basic configuration Volume Discount | 24.73 € *Unit price with basic configuration Volume Discount | 23.17 € *Unit price with basic configuration | 30.20 € *Unit price with basic configuration Volume Discount | 21.73 € *Unit price with basic configuration Volume Discount | 27.13 € *Unit price with basic configuration | 30.48 € *Unit price with basic configuration Volume Discount | 39.15 € *Unit price with basic configuration Volume Discount | 41.25 € *Unit price with basic configuration | 31.88 € *Unit price with basic configuration Volume Discount | 45.80 € *Unit price with basic configuration | 168.46 € *Unit price with basic configuration | 27.23 € *Unit price with basic configuration Volume Discount | 19.82 € *Unit price with basic configuration Volume Discount | 24.43 € *Unit price with basic configuration | 31.64 € *Unit price with basic configuration Volume Discount |
| Min. Shipping Days ： | Same day | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | Same day | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 8 Days | 6 Days | Same day | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days | 6 Days |
| Screw Types | Meter / Unified | Meter / Unified | Meter | Meter | Meter | Meter | Meter / Unified | Meter | Meter / Unified / Taper for Pipe | Meter | Meter | Meter / Unified | Meter | Meter | Meter | Meter | Meter / Unified | Meter / Unified | Meter | Meter | Meter | Meter | Meter | Meter | Meter | Meter | Meter | Meter / Taper for Pipe / Parallel for Pipes | Meter | Meter | Meter | Meter | Meter | Meter | Meter | Taper for Pipe | Taper for Pipe | Taper for Pipe | Taper for Pipe | Taper for Pipe | Taper for Pipe | Taper for Pipe | Meter / Unified | Meter | Miniature |
| Screw size (Nominal) | 1-8UNC ～ M56 | M1 ～ M12 | M2 ～ M24 | M2 ～ M20 | M2 ～ M24 | M3 ～ M16 | - | M3 ～ M12 | - | M6 ～ M12 | - | M1 ～ M12 | M3 ～ M16 | M3 ～ M12 | M2 ～ M24 | M6 ～ M12 | No0UN ～ M20 | 1/2-20UNF ～ M24 | M4 ～ M8 | M2 ～ M24 | M8 | M8 | M1.4 ～ M16 | M3 ～ M16 | M3 ～ M12 | M3 ～ M10 | M10 | - | M1.4 ～ M42 | M3 ～ M24 | M8 ～ M10 | M4 ～ M6 | M3 ～ M14 | M3 ～ M14 | M3 ～ M30 | R1 ～ R3/8 | R1 ～ R3/8 | R1 ～ R3/8 | R1 ～ R3/8 | R1 ～ R3/8 | R1/2 ～ R3/8 | R1 ～ R3/8 | M1 ～ No4UN | M3 ～ M12 | S0.5 ～ S0.9 |
| Pitch (P), Number of Threading(mm) | 0.25 ～ 5.5 | 0.25 ～ 56 | 0.25 ～ 3 | 0.4 ～ 2.5 | 0.25 ～ 3 | 0.5 ～ 2 | 0.25 ～ 32 | 0.5 ～ 1.75 | 1 ～ 28 | 1 ～ 1.75 | 0.5 ～ 3 | 0.25 ～ 56 | 0.5 ～ 2 | 0.5 ～ 1.75 | 0.4 ～ 3 | 1 ～ 1.75 | 0.25 ～ 80 | 0.25 ～ 3 | 0.7 ～ 1.25 | 0.4 ～ 3 | 1.25 | 1.25 | 0.3 ～ 2 | 0.5 ～ 2 | 0.5 ～ 1.75 | 0.5 ～ 1.5 | 1.5 | 1 ～ 19 | 0.3 ～ 4.5 | 0.5 ～ 3 | 1 ～ 1.25 | 0.7 ～ 1 | 0.5 ～ 2 | 0.5 ～ 2 | 0.5 ～ 3.5 | 11 ～ 28 | 11 ～ 28 | 11 ～ 28 | 11 ～ 28 | 11 ～ 28 | 14 ～ 28 | 11 ～ 28 | 0.25 ～ 56 | 0.5 ～ 1.75 | .02 ～ 0.225 |
| Chamfer threads (Lcf) | 1.5P ～ 2.5P | 2P ～ 4P | 5P | 3P | 2.5P | 2.5P | - | 2.5P ～ 5P | - | - | - | 2P ～ 4P | 3P | 2.5P ～ 5P | 1.5P ～ 5P | - | 2P ～ 4P | 5P | 2.5P | 2.5P | 5P | 2P | 2.5P | 2.5P | 2.5P | 3P | 2.5P | - | 5P | 5P | 5P | 5P | 6P | 5P | 6P | 2.5P | 2.5P | 2.5P | 2.5P | 3P | 3P | 2.5P | 2P | 2P ～ 4P | 2P |
| Tool Material Type | Powder high-speed steel / Vanadium High-Speed Steel | Powder high-speed steel | Powder high-speed steel | Carbide | Powder high-speed steel | Vanadium High-Speed Steel | Carbide | Powder high-speed steel | Carbide | Carbide | Carbide | Powder high-speed steel | Vanadium High-Speed Steel | Carbide | Vanadium High-Speed Steel | Carbide | Vanadium High-Speed Steel | Powder high-speed steel | Powder high-speed steel | Vanadium High-Speed Steel | Powder high-speed steel | High-speed steel | Vanadium High-Speed Steel | Vanadium High-Speed Steel | Powder high-speed steel | Vanadium High-Speed Steel | Vanadium High-Speed Steel | Cobalt HSS | Vanadium High-Speed Steel | Vanadium High-Speed Steel | Vanadium High-Speed Steel | Vanadium High-Speed Steel | Vanadium High-Speed Steel | Vanadium High-Speed Steel | Vanadium High-Speed Steel | Vanadium High-Speed Steel | Carbide | Carbide | Vanadium High-Speed Steel | Powder high-speed steel | Carbide | Vanadium High-Speed Steel | Powder high-speed steel | Vanadium High-Speed Steel | Powder high-speed steel |
| work material | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[◎] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Ductile Cast Iron (FCD)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[◎] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[◎] / Alloy Steel (SCM)[◎] / Stainless Steel (JIS-SUS)[◎] / Quenched and tempered steel (25 to 35 HRC)[○] / Quenched and tempered steel (35 to 45 HRC)[○] / Steel casting (SC)[○] / Copper (Cu)[◎] / Brass (Bs)[◎] / Brass cast iron (BsC)[◎] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[◎] / Aluminum Alloy Casting (AC, ADC)[◎] / Zinc Alloy Casting (ZDC)[◎] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[◎] / Alloy Steel (SCM)[◎] / Stainless Steel (JIS-SUS)[◎] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[◎] / Ductile Cast Iron (FCD)[◎] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] / Titanium Alloy (Ti-6Al-4V, etc)[○] | High Hardness Steel (50-60 HRC)[◎] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[◎] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Ductile Cast Iron (FCD)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[◎] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[◎] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Ductile Cast Iron (FCD)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[◎] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○/◎] / Quenched and tempered steel (25 to 35 HRC)[◎] / Quenched and tempered steel (35 to 45 HRC)[◎] / Quenched and tempered steel (45 to 55 HRC)[◎] / High Hardness Steel (50-60 HRC)[○] / Steel casting (SC)[○] / Cast Iron (FC)[○] / Ductile Cast Iron (FCD)[○] / Brass cast iron (BsC)[○/◎] / Aluminum Rolled Material (AL)[○/◎] / Aluminum Alloy Casting (AC, ADC)[○/◎] / Magnesium Alloy (MC)[○/◎] / Zinc Alloy Casting (ZDC)[○/◎] / Titanium Alloy (Ti-6Al-4V, etc)[○/◎] / Nickel-based alloy (Inconel, etc.)[◎] / Thermosetting plastic (bakelite, phenol, etc.)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Quenched and tempered steel (45 to 55 HRC)[◎] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Steel casting (SC)[○] / Cast Iron (FC)[○] / Ductile Cast Iron (FCD)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[◎] / Aluminum Alloy Casting (AC, ADC)[◎] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] / Titanium Alloy (Ti-6Al-4V, etc)[◎] / Nickel-based alloy (Inconel, etc.)[◎] / Thermosetting plastic (bakelite, phenol, etc.)[◎] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[◎] | Cast Iron (FC)[◎] / Ductile Cast Iron (FCD)[◎] / Copper (Cu)[○] / Brass (Bs)[◎] / Brass cast iron (BsC)[◎] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[◎] / Aluminum Alloy Casting (AC, ADC)[◎] / Magnesium Alloy (MC)[◎] / Zinc Alloy Casting (ZDC)[◎] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[◎] / Alloy Steel (SCM)[◎] / Stainless Steel (JIS-SUS)[○] / Quenched and tempered steel (25 to 35 HRC)[◎] / Quenched and tempered steel (35 to 45 HRC)[◎] / Steel casting (SC)[○] / Cast Iron (FC)[○] / Ductile Cast Iron (FCD)[○] / Thermosetting plastic (bakelite, phenol, etc.)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[◎] / Alloy Steel (SCM)[◎] / Stainless Steel (JIS-SUS)[◎] / Steel casting (SC)[○] / Copper (Cu)[◎] / Brass (Bs)[◎] / Brass cast iron (BsC)[◎] / Aluminum Rolled Material (AL)[◎] / Aluminum Alloy Casting (AC, ADC)[◎] / Zinc Alloy Casting (ZDC)[◎] | Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[◎] / Magnesium Alloy (MC)[◎] / Zinc Alloy Casting (ZDC)[◎] | Quenched and tempered steel (45 to 55 HRC)[◎] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Quenched and tempered steel (35 to 45 HRC)[○] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] | Cast Iron (FC)[◎] / Ductile Cast Iron (FCD)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Aluminum Alloy Casting (AC, ADC)[◎] / Magnesium Alloy (MC)[◎] / Zinc Alloy Casting (ZDC)[◎] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[◎] / Steel casting (SC)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Zinc Alloy Casting (ZDC)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[◎] / Alloy Steel (SCM)[◎] / Stainless Steel (JIS-SUS)[◎] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[◎] / Ductile Cast Iron (FCD)[◎] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] / Titanium Alloy (Ti-6Al-4V, etc)[○] | Nickel-based alloy (Inconel, etc.)[◎] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / Alloy Steel (SCM)[◎] / Stainless Steel (JIS-SUS)[◎] | Nickel-based alloy (Inconel, etc.)[◎] | Aluminum Rolled Material (AL)[◎] / Aluminum Alloy Casting (AC, ADC)[◎] / Zinc Alloy Casting (ZDC)[◎] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Ductile Cast Iron (FCD)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Ductile Cast Iron (FCD)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[◎] / Quenched and tempered steel (25 to 35 HRC)[◎] / Quenched and tempered steel (35 to 45 HRC)[◎] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Steel casting (SC)[○] / Copper (Cu)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Stainless Steel (JIS-SUS)[○] / Copper (Cu)[◎] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Quenched and tempered steel (35 to 45 HRC)[○] / Steel casting (SC)[○] / Cast Iron (FC)[○] / Ductile Cast Iron (FCD)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] / Thermosetting plastic (bakelite, phenol, etc.)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[◎] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Ductile Cast Iron (FCD)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] / Titanium Alloy (Ti-6Al-4V, etc)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[◎] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[○] / Ductile Cast Iron (FCD)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] / Titanium Alloy (Ti-6Al-4V, etc)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[◎] / Alloy Steel (SCM)[◎] / Stainless Steel (JIS-SUS)[◎] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[◎] / Ductile Cast Iron (FCD)[◎] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] / Titanium Alloy (Ti-6Al-4V, etc)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[◎] / Alloy Steel (SCM)[◎] / Stainless Steel (JIS-SUS)[◎] / Tool Steel (Before SKD Hardening)[○] / Steel casting (SC)[◎] / Cast Iron (FC)[○] / Ductile Cast Iron (FCD)[○/◎] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] / Titanium Alloy (Ti-6Al-4V, etc)[○] / Nickel-based alloy (Inconel, etc.)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Quenched and tempered steel (35 to 45 HRC)[○] / Steel casting (SC)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[◎] / Zinc Alloy Casting (ZDC)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Quenched and tempered steel (35 to 45 HRC)[○] / Steel casting (SC)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[◎] / Zinc Alloy Casting (ZDC)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[○] / Quenched and tempered steel (25 to 35 HRC)[○] / Quenched and tempered steel (35 to 45 HRC)[○] / Steel casting (SC)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[◎] / Zinc Alloy Casting (ZDC)[○] / Thermoplastic plastic (vinyl chloride, nylon, etc.)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[◎] / Alloy Steel (SCM)[◎] / Quenched and tempered steel (25 to 35 HRC)[○] / Quenched and tempered steel (35 to 45 HRC)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / Stainless Steel (JIS-SUS)[◎] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / Stainless Steel (JIS-SUS)[◎] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[◎] / Alloy Steel (SCM)[◎] / Quenched and tempered steel (25 to 35 HRC)[○] / Quenched and tempered steel (35 to 45 HRC)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Bronze (Pb)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Magnesium Alloy (MC)[○] / Zinc Alloy Casting (ZDC)[○] | Quenched and tempered steel (45 to 55 HRC)[◎] | High Hardness Steel (50-60 HRC)[◎] | Copper (Cu)[○] / Aluminum Rolled Material (AL)[◎] / Aluminum Alloy Casting (AC, ADC)[◎] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Medium carbon steel (carbon content 0.25 to 0.45%)[◎] / High Carbon Steel (C with a content over 0.45%)[◎] / Alloy Steel (SCM)[◎] / Stainless Steel (JIS-SUS)[◎] / Copper (Cu)[◎] / Brass (Bs)[◎] / Brass cast iron (BsC)[◎] / Aluminum Rolled Material (AL)[◎] / Aluminum Alloy Casting (AC, ADC)[◎] / Zinc Alloy Casting (ZDC)[◎] | Low-Carbon Steel (carbon alloy less than 0.25%)[○] / Medium carbon steel (carbon content 0.25 to 0.45%)[○] / High Carbon Steel (C with a content over 0.45%)[○] / Alloy Steel (SCM)[○] / Stainless Steel (JIS-SUS)[◎] / Steel casting (SC)[○] / Copper (Cu)[○] / Brass (Bs)[○] / Brass cast iron (BsC)[○] / Aluminum Rolled Material (AL)[○] / Aluminum Alloy Casting (AC, ADC)[○] / Zinc Alloy Casting (ZDC)[○] | Low-Carbon Steel (carbon alloy less than 0.25%)[◎] / Stainless Steel (JIS-SUS)[◎] / Aluminum Rolled Material (AL)[◎] / Aluminum Alloy Casting (AC, ADC)[◎] / Zinc Alloy Casting (ZDC)[◎] |
| Tap Type | Spiral Tap | Roll tap | Point tap | Hand Tap | Spiral Tap | Spiral Tap | Thread cutter | Hand Tap | Thread cutter | Thread cutter | Thread cutter | Roll tap | Spiral Tap | Hand Tap | Hand Tap | Thread cutter | Roll tap | Point tap | Spiral Tap | Spiral Tap | Point tap | Roll tap | Spiral Tap | Spiral Tap | Spiral Tap | Spiral Tap | Spiral Tap | Thread cutter | Point tap | Point tap | Point tap | Point tap | Point tap | Point tap | Point tap | Tap for pipes | Tap for pipes | Tap for pipes | Tap for pipes | Tap for pipes | Tap for pipes | Tap for pipes | Roll tap | Roll tap | Roll tap |
| Hole type | For blind hole | For blind hole | For through hole | For through hole / For blind hole | For blind hole | For blind hole | For through hole / For blind hole | For through hole / For blind hole | For through hole / For blind hole | For blind hole | For through hole / For blind hole | For blind hole | For blind hole | For through hole / For blind hole | For through hole / For blind hole | For through hole / For blind hole | For blind hole | For through hole | For through hole | For blind hole | For blind hole | For through hole / For blind hole | For blind hole | For blind hole | For blind hole | For blind hole | For blind hole | For through hole / For blind hole | For through hole | For through hole | For through hole | For through hole | For through hole | For through hole | For through hole | For through hole / For blind hole | For through hole / For blind hole | For through hole / For blind hole | For through hole / For blind hole | For through hole / For blind hole | For through hole / For blind hole | For through hole / For blind hole | For blind hole | For through hole / For blind hole | For blind hole |
| Coating Y/N | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available | Available |
| Coating Type | Other | TiCN | Other | TiCN / Other | Other | Other | For High Hardness (Silicon Group) / Other | TiCN | TiAlN | TiAlN | TiAlN | TiCN | Other | TiCN | TiN | TiAlN | TiN | Other | Other | TiN / CrN | Other | Non-Coated | TiN | TiN | TiCN | TiN | CrN | TiN | TiN | TiN | TiCN | TiCN | TiN | TiN | TiN | TiN | TiN | TiN | TiN | TiCN | TiCN | TiCN | TiCN | TiN | CrN |
| Overall Length (L)(mm) | 34 ～ 250 | 30 ～ 82 | 80 ～ 200 | 40 ～ 105 | 80 ～ 200 | 46 ～ 95 | 40 | 46 ～ 82 | 60 ～ 120 | 62 ～ 89 | 60 ～ 120 | 60 ～ 200 | 46 ～ 95 | 46 ～ 82 | 40 ～ 120 | 62 ～ 89 | 30 ～ 105 | 34 ～ 120 | 52 ～ 70 | 40 ～ 120 | 70 | 150 | 34 ～ 95 | 100 ～ 150 | 46 ～ 82 | 100 ～ 150 | 75 | 80 ～ 210 | 34 ～ 175 | 100 ～ 200 | 70 ～ 75 | 100 | 46 ～ 88 | 46 ～ 88 | 100 ～ 200 | 55 ～ 95 | 55 ～ 95 | 55 ～ 95 | 55 ～ 95 | 59 ～ 109 | 59 ～ 87 | 55 ～ 95 | 30 ～ 46 | 80 ～ 150 | 30 |
Loading...
Filter by:
Stock
-
- Stock Items Included
Narrow search by specifying spec./dim.
-
Screw Types
- Meter
- Unified
- Whitworth
- Sewing Machine
- Taper for Pipe
- Parallel for Pipes
- Miniature
- Other
-
Screw size (Nominal)
- CTG-22
- CTG-16
- No0UN
- NO.0-80UNF
- S0.1
- NO.1-72UNF
- NO.1-64UNC
- NO.10-32UNF
- No.10-32UNF
- NO.10-24UNC
- No.10-24UNC
- NO.12-28UNF
- NO.12-24UNC
- S0.2
- NO.2-64UNF
- NO.2-56UNC
- No.2-56UNC
- S0.3
- NO.3-56UNF
- NO.3-48UNC
- No.4
- S0.4
- NO.4-48UNF
- NO.4-40UNC
- No.4-40UNC
- S0.5
- NO.5-44UNF
- NO.5-40UNC
- No.5-40UNC
- No.6
- S0.6
- NO.6-40UNF
- No.6-32UNC
- S0.7
- S0.8
- NO.8-36UNF
- NO.8-32UNC
- No.8-32UNC
- S0.9
- 1UN
- 1UNS
- G1
- G 1"
- M1
- NPS1
- NPT1
- NPTF1
- No1UN
- PF1
- PF 1
- R1
- Rp1
- S1
- UNC 1
- UNC 1"
- UNF 1"
- W1
- 1´-11
- 1′-11
- 1-8UNC
- 1'-8UNC
- G1"-3"
- 1"1/2UN
- G1"1/2
- NPS1"1/2
- NPT1"1/2
- R1"1/2
- Rp1"1/2
- W1"1/2
- 1′1/2-11
- 1 1/2-8UN
- 1"1/4UN
- G1"1/4
- NPS1"1/4
- NPT1"1/4
- R1"1/4
- Rp1"1/4
- W1"1/4
- 1 1/4-8UN
- 1"1/8UN
- G1"1/8
- R1"1/8
- W1"1/8
- 1 1/8-8UN
- 1"1/16UN
- 1/2
- 1/2UN
- G1/2
- G 1/2
- NPS1/2
- NPT1/2
- NPTF1/2
- PF 1/2
- R1/2
- Rc1/2
- Rp1/2
- UNC 1/2
- UNF 1/2
- UNJF 1/2
- W1/2
- 1/2-20UNF
- 1/2-14
- 1/2-13UNC
- G1/2 5/8
- 1"3/4UN
- G1"3/4
- R1"3/4
- Rp1"3/4
- W1"3/4
- 1 3/4-8UN
- 1"3/8UN
- G1"3/8
- R1"3/8
- W1"3/8
- 1 3/8-8UN
- 1/4
- 1/4UN
- G1/4
- G 1/4
- NPS1/4
- NPT1/4
- NPTF1/4
- PF1/4
- PF 1/4
- PT 1/4
- R1/4
- Rc1/4
- Rp1/4
- SM1/4
- UNC 1/4
- UNF 1/4
- UNJF 1/4
- W1/4
- 1/4-28UNF
- 1/4-20UNC
- W1"5/8
- 1 5/8-8UN
- W1"7/8
- 1 7/8-8UN
- 1/8
- G1/8
- G 1/8
- NPS1/8
- NPT1/8
- NPTF1/8
- PF1/8
- PT 1/8
- R1/8
- Rc1/8
- Rp1/8
- SM1/8
- W1/8
- 1/8-28
- 1/16
- G1/16
- NPS1/16
- NPT1/16
- R1/16
- Rp1/16
- M1.1
- G 1.1/2
- G 1.1/4
- G 1.1/8
- M1.2
- S1.2
- M1.4
- S1.4
- M1.6
- M1.7
- M1.8
- 2UN
- G2
- M2
- M2.0
- NPS2
- NPT2
- No2UN
- R2
- Rp2
- UNC 2
- UNF 2
- W2
- 2-8UN
- G2"1/2
- R2"1/2
- Rp2"1/2
- W2"1/4
- M2.2
- M2.3
- M2.5
- M2.6
- EGM 3
- G3
- M3
- M3.0
- No3UN
- R3
- Rp3
- UNC 3
- UNF 3
- G3"1/2
- R3"1/2
- Rp3"1/2
- 3/4
- 3/4UN
- G3/4
- G 3/4
- NPS3/4
- NPT3/4
- NPTF3/4
- PF 3/4
- R3/4
- Rp3/4
- UNC 3/4
- UNF 3/4
- W3/4
- 3/4-16UNF
- 3/4-14
- 3/4-10UNC
- 3/8UN
- G3/8
- G 3/8
- NPS3/8
- NPT3/8
- NPTF3/8
- PF3/8
- PF 3/8
- PT 3/8
- R3/8
- Rc3/8
- Rp3/8
- UNC 3/8
- UNF 3/8
- UNJF 3/8
- W3/8
- 3/8-24UNF
- 3/8-19
- 3/8-16UNC
- 3/8W16
- M3 - M10
- M3～10
- M3 - M12
- SM3/16
- W3/16
- M3 - M18
- SM3/32
- M3.5
- EGM 4
- G4
- M4
- M4.0
- MF4
- No4UN
- R4
- Rp4
- UNC 4
- UNF 4
- №4-40UNC
- M4～6
- M4.5
- EGM 5
- M5
- M5.0
- MF5
- No5UN
- UNC 5
- №5-40UNC
- 5/8UN
- G5/8
- G 5/8
- R5/8
- UNC 5/8
- UNF 5/8
- W5/8
- 5/8-18UNF
- 5/8-11UNC
- G5/8 3/4
- M5 - M12
- 5/16UN
- UNC 5/16
- UNF 5/16
- UNJF 5/16
- W5/16
- 5/16-24UNF
- 5/16-18UNC
- 5/16W18
- W5/32
- M5.5
- EGM 6
- M6
- M6.0
- MF6
- No6UN
- UNC 6
- UNF 6
- UNJC 6
- №6-32UNC
- M7
- MF7
- PG7
- 7 execution M3 - M12
- 7/8UN
- G7/8
- G 7/8
- R7/8
- UNC 7/8
- UNF 7/8
- W7/8
- 7/8-14UNF
- 7/8-9UNC
- 7/16UN
- UNC 7/16
- UNF 7/16
- UNJF 7/16
- 7/16-20UNF
- 7/16-14UNC
- SM7/32
- EGM 8
- M8
- MF8
- No8UN
- UNC 8
- UNF 8
- UNJC 8
- №8-32UNC
- M9
- PG9
- 9/16
- 9/16UN
- UNC 9/16
- UNF 9/16
- 9/16-18UNF
- 9/16-12UNC
- SM9/32
- SM9/64
- EGM 10
- M10
- MF10
- No10UN
- UNC10
- UNC 10
- UNF 10
- UNJF 10
- №10-32UNF
- №10-24UNC
- M10～25
- M11
- SM11/32
- SM11/64
- EGM 12
- M12
- MF12
- Mf12
- No12UN
- UNC 12
- UNF 12
- M12 x 1.5
- M13
- PG13.5
- M14
- MF14
- M15
- SM15/64
- M16
- MF16
- Mf16
- M16 x 1.5
- M17
- M18
- MF18
- M19
- M20
- MF20
- Mf20
- M20 x 1.5
- M21
- M22
- MF22
- M23
- M24
- MF24
- M25
- MF25
- Mf25
- M25 x 1.5
- M26
- MF26
- M27
- MF27
- M28
- MF28
- M30
- MF30
- M32
- Mf32
- M33
- M34
- M35
- M36
- M37
- M38
- M39
- M40
- M42
- M45
- M48
- M52
- M56
- M64
-
Pitch (P), Number of Threading(mm)
-
Chamfer threads (Lcf)
-
Tool Material Type
-
work material
- Low-Carbon Steel (carbon alloy less than 0.25%)
- Medium carbon steel (carbon content 0.25 to 0.45%)
- High Carbon Steel (C with a content over 0.45%)
- Alloy Steel (SCM)
- Stainless Steel (JIS-SUS)
- Quenched and tempered steel (25 to 35 HRC)
- Quenched and tempered steel (35 to 45 HRC)
- Quenched and tempered steel (45 to 55 HRC)
- High Hardness Steel (50-60 HRC)
- Tool Steel (Before SKD Hardening)
- Steel casting (SC)
- Cast Iron (FC)
- Ductile Cast Iron (FCD)
- Copper (Cu)
- Brass (Bs)
- Brass cast iron (BsC)
- Bronze (Pb)
- Aluminum Rolled Material (AL)
- Aluminum Alloy Casting (AC, ADC)
- Magnesium Alloy (MC)
- Zinc Alloy Casting (ZDC)
- Titanium Alloy (Ti-6Al-4V, etc)
- Nickel-based alloy (Inconel, etc.)
- Thermosetting plastic (bakelite, phenol, etc.)
- Thermoplastic plastic (vinyl chloride, nylon, etc.)
-
Tap Type
-
Hole type
-
Coating Y/N
-
Coating Type
-
Overall Length (L)(mm)
Narrow search by specifying Brand
-
- MISUMI (8)
- OSG (55)
- CARMEX (35)
- YAMAWA MFG (18)
- SANDVIK (5)
- TANOI MFG (4)
- GUHRING (3)
- NACHI(FUJIKOSHI) (3)
- EIKOSHA (2)
- NS TOOL (2)
- BERNSTEIN AG (0)
- KANETEC (0)
- MITSUTOMO (0)
- NEW STRONG (0)
- STAHLWILLE (0)
- RUKO (0)
- BAHCO (0)
- ENGINEER (0)
- LIGHTSEIKI (0)
- SKC (0)
- HAZET (0)
- ISHIHASHI (0)
- TRUSCO NAKAYAMA (0)
- WERA (0)
- WIHA (0)
- FEIN (0)
- RENNSTEIG (0)
- GEDORE (0)
- ESCO (0)
- REX TOOLS (0)
- NOGAJAPAN (0)
Narrow search by specifying CAD data type
-
- 2D
- 3D
Categories related to Screw-Hole-Related Tools
Método de pago
Factura
Prepago
Fabricación bajo demanda
Certificados
Copyright © MISUMI Corporation All Rights Reserved.