SKF Bearing Covers, Seals（Page 2）

?* Information on days to ship and prices

• 

  Housing seals L Series / Internal diameter 50~165mm

  SKF

  [Specifications]
  ・Internal diameter(mm): 50~165
  ・Outer diameter(mm): 84.6~202.6
  ・eClass code: 23-05-17-90
  
  SKF housing seals are the first barrier against contamination. The four-lip seals replace the former double-lip seals. The four-lip seals are more effective than the double-lip and generate less friction, which enables higher shaft speeds. For highly contaminated environments, SKF recommends the three-barrier solution. This cost-effective sealing solution can have a significant impact on bearing service life as contaminants have to pass through three barriers to reach the bearing.
  
  [Features]
  ・Good protection from contamination
  ・Keep the lubricant in the housing
  ・Part of three barrier solution

  Starting from∗ ：	15.12 €
  Min. Shipping Days ：	12 Days

  *Unit price with basic configuration

• 

  SKF End Cover for Y- and ConCentra Bearing Units

  SKF

  [Specifications]
  ・Width A(mm): 23~35.5
  ・Exterior diameter D(mm): 44.1~85.8
  ・eClass code: 23-05-17-90
  
  End covers protect the exposed shaft end and help to avoid accidents. They have good resistance to most chemicals and can withstand operating temperatures up to 100 °C (210 °F). They are easy to install and are cost effective. Most ball bearing units can accommodate specifically designed end covers.
  
  [Features]
  ・Easy to install
  ・Good chemical resistance
  ・Cost effective

  Starting from∗ ：	2.46 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  SKF V-Ring Seal for Pedestal Bearing Housing

  SKF

  [Specifications]
  ・Engineering material: Nitrile rubber/Steel
  ・eClass code: 23-05-17-90
  
  V-ring seals consist of a V-ring and a sheet steel sealing washer with a vulcanized rubber lip. The rubber lip fits into the seal groove in the housing. The washer is protected against corrosion. The seals are used to protect bearings from contamination or as secondary seals to protect primary seals in highly contaminated environments. They are a cost-effective and easy to install contaminant barrier for all kind of shafts. They are available in nitrile rubber.
  
  [Features]
  ・Easy to install
  ・Many variants
  ・Cost-effective

  Starting from∗ ：	19.86 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  End Cover

  SKF

  End covers protect the exposed shaft end and help to avoid accidents. They have good resistance to most chemicals and can withstand operating temperatures up to 100 °C (210 °F). They are easy to install and are cost effective. Most ball bearing units can accommodate specifically designed end covers.
  
  [Features]
  ・Easy to install
  ・Good chemical resistance
  ・Cost effective
  ・eClass code: 23-05-17-90
  ・ECW, ECY

  Starting from∗ ：	3.25 €
  Min. Shipping Days ：	12 Days

  *Unit price with basic configuration

• 

  End Cover, Closed

  SKF

  End covers protect the exposed shaft end and help to avoid accidents. They have good resistance to most chemicals and can withstand operating temperatures up to 100 °C (210 °F). They are easy to install and are cost effective. Most ball bearing units can accommodate specifically designed end covers.
  
  [Features]
  ・Easy to install
  ・Good chemical resistance
  ・Cost effective
  ・eClass code: 23-05-17-90
  ・ECL, ECY

  Starting from∗ ：	5.21 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  End Cover, Thermoplastic Polyurethane

  SKF

  End covers protect the exposed shaft end and help to avoid accidents. They have good resistance to most chemicals and can withstand operating temperatures up to 100 °C (210 °F). They are easy to install and are cost effective. Most ball bearing units can accommodate specifically designed end covers.
  
  [Features]
  ・Easy to install
  ・Good chemical resistance
  ・Cost effective
  ・eClass code: 23-05-17-90
  ・ECB

  Starting from∗ ：	4.55 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  Four-lip Sealing Set

  SKF

  [Specifications]
  ・Material: elastomer/ thermoplastic
  ・eClass code: 23-05-17-90
  
  SKF housing seals are the first barrier against contamination. The four-lip seals replace the former double-lip seals. The four-lip seals are more effective than the double-lip and generate less friction, which enables higher shaft speeds. For highly contaminated environments, SKF recommends the three-barrier solution. This cost-effective sealing solution can have a significant impact on bearing service life as contaminants have to pass through three barriers to reach the bearing.
  
  [Features]
  ・Good protection from contamination
  ・Keep the lubricant in the housing
  ・Part of three barrier solution

  Starting from∗ ：	54.62 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  L-section Ring

  SKF

  [Specifications]
  ・Internal diameter(mm): 90
  ・Outer diameter(mm): 124.2
  ・Material: elastomer/ thermoplastic
  ・eClass code: 23-05-17-90
  
  Angle rings (L-shaped thrust collars) are used either with NU design cylindrical roller bearings to locate the shaft axially in one direction, or with NJ design bearings to locate the shaft axially in both directions. The rings are made of carbon chromium steel and are hardened and ground. They are supplied as separate components.
  
  [Features]
  ・Locate the shaft axially if there are no NJ or NUP design locating bearings within the product range
  ・Provide an extended inner ring seat for heavily loaded bearings in the locating position
  ・Simplify design or mounting procedures

  Starting from∗ ：	239.70 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  Sealing Strip

  SKF

  [Specifications]
  ・Width(mm):6, 8
  ・Length(mm): 190, 260
  ・eClass code: 23-05-17-90
  
  Felt strips, and their high-temperature variants made of aluminium borosilicate, provide a simple and effective sealing solution. They accommodate relatively high shaft speeds, because a small gap forms between the felt strip and the shaft, transforming the seal into a non-contact, gap-type seal. Felt strips should be cut to the correct length and soaked in hot oil prior to being installed.
  
  [Features]
  ・Cost-effective
  ・Suitable for relatively high shaft speeds

  Starting from∗ ：	16.22 €
  Min. Shipping Days ：	12 Days

  *Unit price with basic configuration

• 

  Shaft Seal, CRW1 S, VMQ

  SKF

  [Specifications]
  ・Internal diameter(mm): 53.98
  ・Outer diameter(mm): 73
  ・eClass code: 23-07-08-01
  
  Radial shaft seals are used between rotating and stationary machine components, or between components in relative motion. CRW1 seals are designed with a metal case, an SKF WAVE lip made of elastomer with higher pumping rate to reduce heat generation, and a garter spring to optimize sealing against the shaft. Most of the seals feature the SKF Bore Tite coating on the outside diameter that helps fill small imperfections in the housing bore.
  
  [Features]
  ・For oil or grease
  ・With garter spring
  ・WAVE lip creates higher pumping rate
  ・WAVE lip has less friction between shaft and lip
  ・WAVE lip has a lower temperature at the contact point

  Starting from∗ ：	22.93 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  Shaft Seal, CRWA1 R, NBR

  SKF

  [Specifications]
  ・Internal diameter(mm): 41.28, 44.45, 50.8
  ・Outer diameter(mm): 61.9, 63.55, 66.62
  ・eClass code: 23-07-08-01
  
  Radial shaft seals are used between rotating and stationary machine components, or between components in relative motion. CRWA1 seals are designed with a metal case, an SKF WAVE lip made of elastomer with higher pumping rate to reduce heat generation, a garter spring to optimize sealing against the shaft, and a dust lip to improve contamination exclusion. Most of the seals feature the SKF Bore Tite coating on the outside diameter that helps fill small imperfections in the housing bore.
  
  [Features]
  ・For oil or grease
  ・With garter spring
  ・WAVE lip creates higher pumping rate
  ・WAVE lip has less friction between shaft and lip
  ・WAVE lip has a lower temperature at the contact point

  Starting from∗ ：	6.08 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  Shaft Seal, CRWA1, NBR

  SKF

  [Specifications]
  ・Internal diameter(mm): 31.8
  ・Outer diameter(mm): 44.5
  ・Material: NBR

  Starting from∗ ：	4.82 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  Shaft Seal, CRWH1 R, NBR

  SKF

  [Specifications]
  ・Internal diameter(mm): 101.6
  ・Outer diameter(mm): 133.35
  ・eClass code: 23-07-08-01
  
  Radial shaft seals are used between rotating and stationary machine components, or between components in relative motion. CRWH1 seals are designed with a double metal case, an SKF WAVE lip made of elastomer with a higher pumping rate to reduce heat generation, and a garter spring to optimize sealing against the shaft. Most of the seals feature the SKF Bore Tite coating on the outside diameter that helps fill small imperfections in the housing bore.
  
  [Features]
  ・For oil or grease
  ・With garter spring
  ・WAVE lip creates higher pumping rate
  ・WAVE lip has less friction between shaft and lip
  ・WAVE lip has a lower temperature at the contact point

  Starting from∗ ：	27.55 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  Shaft Seal, CRWH1, NBR

  SKF

  [Specifications]
  ・Internal diameter(mm): 69.85
  ・Outer diameter(mm): 98.45
  ・eClass code: 23-07-08-01
  
  Radial shaft seals are used between rotating and stationary machine components, or between components in relative motion. CRWH1 seals are designed with a double metal case, an SKF WAVE lip made of elastomer with a higher pumping rate to reduce heat generation, and a garter spring to optimize sealing against the shaft. Most of the seals feature the SKF Bore Tite coating on the outside diameter that helps fill small imperfections in the housing bore.
  
  [Features]
  ・For oil or grease
  ・With garter spring
  ・WAVE lip creates higher pumping rate
  ・WAVE lip has less friction between shaft and lip
  ・WAVE lip has a lower temperature at the contact point

  Starting from∗ ：	14.37 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  Shaft Seal, CRWHA1 R, NBR

  SKF

  [Specifications]
  ・Internal diameter(mm): 69.85
  ・Outer diameter(mm): 98.45
  ・eClass code: 23-07-08-01
  
  Radial shaft seals are used between rotating and stationary machine components, or between components in relative motion. CRWHA1 seals are designed with a double metal case, an SKF WAVE lip made of elastomer with a higher pumping rate to reduce heat generation, a garter spring to optimize sealing against the shaft, and a dust lip to improve contamination exclusion. Most of the seals feature the SKF Bore Tite coating on the outside diameter that helps fill small imperfections in the housing bore.
  
  [Features]
  ・For oil or grease
  ・With garter spring
  ・WAVE lip creates higher pumping rate
  ・WAVE lip has less friction between shaft and lip
  ・WAVE lip has a lower temperature at the contact point

  Starting from∗ ：	92.32 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  Shaft Seal, FKM, CRWA1

  SKF

  [Specifications]
  ・Internal diameter(mm): 101.6
  ・Outer diameter(mm): 126.97
  ・Material: FKM

  Starting from∗ ：	58.38 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  Shaft Seal, HM14 R, NBR

  SKF

  [Specifications]
  ・Internal diameter(mm): 28.58, 57.15
  ・Outer diameter(mm): 34.93, 66.68
  ・Material: NBR

  Starting from∗ ：	3.08 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

Loading...